Page 1
Final dimension: A5 S411135 13.06.2017 S955EPQ Seghetto alternativo ISTRUZIONI D’USO Istruzioni originali Jigsaw OPERATING INSTRUCTIONS Translation of the original instructions ATTENZIONE! Prima di usare la macchina, leggete e comprendete le istruzioni di sicurezza e le istruzioni d’uso fornite WARNING! Before using the machine, read and understand the supplied safety instructions and operating instructions...
è conforme ai requisiti essenziali di sicurezza e file is in salute contenuti nelle seguenti direttive europee: 2006/42/CE, 2014/30/CE, 2011/65/CE Valex SpA - Via Lago Maggiore, 24 DECLARATION OF CONFORMITY 36015 Schio (VI) - Italy The firm indicated on the label declares, under 05.2017...
COMPONENTI Fare riferimento alla fig. A e seguenti, allegate alle presenti istruzioni. ATTENZIONE! Il seghetto alternativo è idoneo a tagliare, mediante una specifica 1. Interruttore avvio/arresto lama, pannelli di legno o materiale plastico e 2. Regolatore di velocità lamiere di metallo a basso tenore di carbonio. 3.
- che attorno sia prevista un’ampia zona opera- 7. Rilasciate la leva che dovrà ritornare automa- tiva libera da impedimenti. ticamente nella posizione iniziale e muovete - che vi sia una buona illuminazione. leggermente la lama in modo da favorirne - che sia utilizzata in vicinanza dell’interruttore l’innesto.
Page 10
premere l’interruttore (1) e poi rilasciarlo subito. Materiale TPI denti Materiale Finitura del ta- ATTENZIONE! In caso di interruzione per pollice lama glio e dei bordi dell’alimentazione elettrica, posizionare l’in- (25,4mm) (in funzione del terruttore nella posizione di arresto, in modo numero di denti) da evitare un riavvio inatteso.
Page 11
Indossate i dispositivi di protezione individuale Materiali Velocità Movimento pendolare (non inclusi). Vedi ‘ISTRUZIONI DI SICUREZZA’. Legno e pannelli di Massimo (posizione Alte masonite 2 o 3) 1. Impugnate l’utensile con la mano. Il cavo di alimentazione deve essere tenuto lontano Materiali plastici, Medie Minimo (posizione 1)
opposta), appoggiatelo al banco e staccate agenti chimici. la spina dall’alimentazione elettrica. - Eliminate eventuali tracce di resina che si depositeranno sull’utensile. Nel taglio dei metalli raffreddate costantemente la - Prestate particolare attenzione alla pulizia lama versando delle gocce di olio da taglio (non dell’interruttore, alle feritoie di ventilazione del incluso), in caso contrario si avrà...
PROBLEMI, CAUSE E RIMEDI IMMAGAZZINAMENTO Effettuate una accurata pulizia di tutto l’utensile PROBLEMA CAUSE RIMEDI e sue parti accessorie (vedi paragrafo Manuten- zione). Proteggete le parti non verniciate con un L’ u t e n s i l e Linea di alimenta- Verificate la linea olio protettivo ed utilizzate l’imballo originale o la elettrico non...
COMPONENTS Refer to fig. A and the following figures, attached to these instructions. IMPORTANT! The jigsaw is suitable for cutting, by means of a specific blade, panels 1. On/Off switch of wood or plastic material and sheet metal 2. Speed regulator with a low carbon content.
differential switch. CONNECTING TO AN ELECTRICAL VACUUM - that the power supply system is earthed and CLEANER (not included) conforms to the standards (only if the power It is mandatory to connect the dust extraction tool is class 1, which is equipped with a plug adaptor (12) to an electrical vacuum cleaner, with earth cable).
Page 16
and solutions”. During use, the blade wears, loses its sharpness, When not using the tool, switch it off and di- becomes damaged, breaks: always make a vi- sconnect the plug from the socket. sual check before using and replace if necessary. Remember that a successful cut also depends on the blade condition.
Page 17
while the rest of the tool (and the blade) will be workpiece but does not touch it. At this point, at an angle. the blade will be completely exposed once you 1. Unplug from the power supply switch on the power tool. 2.
chips and sawdust will fall to the floor and not nents of the tool and fig.D. If you are not familiar toward you or the tool. with handling and assembling mechanical components, we recommend that you consult Ceiling cuts must be done with extreme caution an authorised service centre.
PROBLEMS, CAUSES AND SOLUTIONS STORAGE Clean the tool and all its accessories thoroughly PROBLEM CAUSE SOLUTION (see Maintenance section). Protect the unpainted parts with protective oil and use the original The power tool The power cord is Check the power packaging or case (where fitted) to protect it.