Video-inserter for opel, chevrolet and buick with cd500, dvd600, dvd800, dvd900, cd600intellilink and dvd950intellilink navigation systems/radios (18 pages)
For dacia vehicles with lg head-unit and renault vehicles with rlink (lg) and medianav head-unit. video-inserter with 2 video inputs + rgb + rear-view camera input and can control. (21 pages)
Video-inserter for bmw vehicles with business/professional cic-e and cic-f series navigation systems or radios with colour display and 4pin hsd lvds monitor plug (15 pages)
Video-inserter for volvo vehicles with rti 2011 infotainment and 5 inch monitor (20 pages)
Summary of Contents for v.link CI-VL2-MIB-2
Page 1
Video-inserter CI-VL2-MIB-2 for VAG Fahrzeuge with MIB High/Standard infotainment systems with 7”/8” or 5.8” monitors Video-inserter with 2 video + RGB + rear-view camera input and CAN control Product features Video-inserter for factory-infotainment monitors 2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …) ...
Video-sources to IN1 and IN2 2.5.2. Audio-switch and audio-insertion 2.5.3. After-market rear-view camera 2.5.4. After-market navigation 2.6. Connecting video-interface and keypad 2.7. Picture settings 2.8. Activation of parking guide lines for rear-view camera 3. Interface operation 4. Specifications 5. Connections (video-interface) Version 18.12.2014 CI-VL2-MIB-2...
Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 18.12.2014 CI-VL2-MIB-2...
To the video interface’s RGB-input it is possible to connect a RGB- or a VGA-video source. Set dip 4 according to table. After-Market Navigation Dip 4 VGA 800x480 (RGB-Input Pin 4 H-Sync, Pin 8 V-Sync) RGB NTSC 400(or480)x240 Version 18.12.2014 CI-VL2-MIB-2...
Audi A3 dient Dip 1 zur Einstellung der Steuerung der Navigation über den Werks- Controller. NAV-FN900D in Audi A3 by Dip 1 Dip 2 Dip 3 Dip 4 Control via cross on the display Direct control Version 18.12.2014 CI-VL2-MIB-2...
If power source is not taken directly from the battery, the connection has to be checked for being start-up proven and permanent. 2.1. Place of installation The interface is installed on the backside of the head-unit. Version 18.12.2014 CI-VL2-MIB-2...
Note: Check LEDs on video-interface after reconnecting the battery, one must be on. Note: No liability for vehicle wire colours and pin definition! Possible changes by the vehicle manufacturer. The given information must be verified by the installer. Version 18.12.2014 CI-VL2-MIB-2...
Remove the female Quadlock connector of the vehicle harness from the rear of the head-unit and connect it to the male Quadlock connector of Quadlock harness. Connect female Quadlock connector of Quadlock harness to the male Quadlock connector of the head-unit. Version 18.12.2014 CI-VL2-MIB-2...
Connect video RCA of the AV-source 1 to the female RCA connector Video 1 of the video cable. Connect video RCA of the AV-source 2 to the female RCA connector Video 2 of the video cable. Version 18.12.2014 CI-VL2-MIB-2...
It is possible to switch the audio signals from the to IN1 and IN2 connected AV-sources parallel to the video-signal of the respective AV-source by video-interface’s built-in audio- switch. Version 18.12.2014 CI-VL2-MIB-2...
Page 12
Audio input signal R/L of source IN2 Audio input signal R/L of source IN1 Audio output signal R/L of factory audio AUX or FM-modulator Ground Note: When switching the video interface from video-IN1 to video-IN2, the audio will also automatically be switched. Version 18.12.2014 CI-VL2-MIB-2...
6pin to 8pin cable at the black 8pin connector and connect it to the reverse gear light (+12V). For this use a relay because the reverse gear light of the vehicle is clocked (relay AC-RW1230 and AC-RS5 optional available). Note: Set Dip 5 to ON. Version 18.12.2014 CI-VL2-MIB-2...
If connecting the after market navigation NAV-FN900D the factory touch-screen can be used (not Audi A3!). Please do the following step, too: Connect female 8pin connector of 6pin to 8pin cable to 8pin connector (Ctrl) of the video-interface. Version 18.12.2014 CI-VL2-MIB-2...
UP and DOWN change the corresponding values. The buttons are embedded in the housing to avoid accidental changes during or after installation. The following settings are available: Brightness Contrast Saturation Position H (horizontal) Position V (vertical) Version 18.12.2014 CI-VL2-MIB-2...
IN1 video IN2 factory video … Inputs which are not enabled are skipped. If the sources are connected to the audio cable, when switching from video IN1 to video IN2, also the sound will be switched. Version 18.12.2014 CI-VL2-MIB-2...
Power consumption 28.4W Video input 0.7V~1V Video input formats PAL/NTSC RGB-video amplitude 0.7V with 75 Ohm impedance Temperature range -40°C to +85°C Weight 368g Dimensions (box only) W x H x D 154 x 22 x 92 mm Version 18.12.2014 CI-VL2-MIB-2...