Draper STORMFORCE 65142 Instructions Manual

Draper STORMFORCE 65142 Instructions Manual

6 piece air hammer kit

Advertisement

Quick Links

6 PIECE AIR
HAMMER KIT
65142
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the STORMFORCE 65142 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Draper STORMFORCE 65142

  • Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
  • Page 2: Title Page 1.1 Introduction

    Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact.
  • Page 3: Table Of Contents

    NOTES CONTENTS 1. TITLE PAGE 1.1 INTRODUCTION......................2 1.2 REVISION HISTORY ....................2 1.3 UNDERSTANDING THIS MANUAL ................2 1.4 COPYRIGHT NOTICE ....................2 2. CONTENTS 2.1 CONTENTS ........................3 3. WARRANTY 3.1 WARRANTY......................... 4 4. INTRODUCTION 4.1 SCOPE......................... 5 4.2 SPECIFICATION ......................
  • Page 4: Warranty

    This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period.
  • Page 5: Scope

    INTRODUCTION 13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS 4.1 SCOPE This composite air hammer can be used for a wide range of applications such as general automotive body shop work and ceramic tile removal. Any other use other than that it was Read the instruction manual.
  • Page 6: Health And Safety Information

    HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully.
  • Page 7: General Safety Instructions For Compressed Air

    HEALTH AND SAFETY INFORMATION 11. MAINTENANCE Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts may Warning! continue to move due to momentum. Wait for all parts to stop; then disconnect it from the air line ●...
  • Page 8: Specific Safety Instructions For Air Hammers

    5.3 SPECIFIC SAFETY INSTRUCTIONS FOR AIR HAMMERS Important: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.
  • Page 9: Residual Risk

    HEALTH AND SAFETY INFORMATION 5.4 RESIDUAL RISK Warning! ● Although the safety instructions and operating manuals for our tools contain extensive instructions of safe working with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms. Power tools must therefore always be operated with caution! - 9 -...
  • Page 10: Technical Description

    TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Retaining spring thread. (2) Trigger. (3) Exhaust port. (4) ¼" BSP air inlet. - 10 -...
  • Page 11: Unpacking And Checking

    Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product.
  • Page 12: Air Supply

    This air tool operates at a maximum pressure of 90psi and must be controlled via a combination pressure regulator, in-line lubricator and moisture filter such as the Draper range (see you local Draper stockist) which with proper maintenance will ensure a constant supply of dry air and lubricating oil at all times (see illustration below).
  • Page 13: Assembly

    ASSEMBLY Warning! ● Failure to follow these instructions will lead to premature malfunction of the equipment which is not covered by the guarantee. NOTE: Disconnect from the air supply before carrying out adjustment, servicing or maintenance. 9.1 CONNECTION TO THE AIR SUPPLY –...
  • Page 14: Operation

    10. OPERATION 10.1 TRIGGER SWITCH - FIG. 4 Note: Before connecting the hammer to the air supply reduce the line pressure according to the specification. Pull trigger (2) to operate the hammer. Release the trigger to stop the hammer. Note: Before tool operation and work commences, ensure the compressor reservoir is drained of condensate along with all connected air lines.
  • Page 15: Maintenance

    11. MAINTENANCE Warning! ● Disconnect from the air supply before carrying out any adjustments, servicing or maintenance. ● Never use any sockets or accessories that are not hardened for impact use. 11.1 EVERY-DAY MAINTENANCE CHECKS Before connection to the air supply: •...
  • Page 16: Troubleshooting

    – 'O' rings throttle valve – Replace 'O' ring or return to dislodged from seat inlet valve. service centre. We recommend the 250ml Stock No.34679 use of Draper Air Stock No.34681 Tool Oil: 500ml Stock No.34682 1Litre - 16 -...
  • Page 17: Explanation Of Symbols

    13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Read the instruction manual. Wear safety glasses. Wear ear defenders. Wear protective gloves. Long and loose hair must be contained or securely tied back. Do not abandon into the environment. Keep out of the reach of children. Warning! Warning! Risk of crushing.
  • Page 18: Disposal

    14. DISPOSAL 14.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: ●...
  • Page 19 NOTES - 19 -...
  • Page 20 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.

Table of Contents