Table of Contents
Advertisement
Quick Links
BRITISH
MADE
APPLICATION GUIDE FOR:
ENGINE
TIMING KIT
15498
This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of
the product. Read all information before operating product.
This guide has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains necessary information to ensure its correct and safe use. By following the information contained in
this guide, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this guide are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this guide, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper 15498
Summary of Contents for Draper 15498
- Page 1 By following the information contained in this guide, it will ensure both product and operator safety, together with longer life of the product itself. AlI photographs and drawings in this guide are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Introduction
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 1. TITLE PAGE 1.1 INTRODUCTION......................2 1.2 REVISION HISTORY ....................2 1.3 UNDERSTANDING THIS GUIDE................. 2 1.4 COPYRIGHT NOTICE ....................2 2. CONTENTS 2.1 CONTENTS ........................3 3. GUARANTEE 3.1 GUARANTEE ....................... 4 4. GENERAL PRODUCT INFORMATION 4.1 GENERAL PRODUCT INFORMATION ............... 5 HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR USE Personal safety...................... -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: General Product Information
This product is designed to be used correctly and with care for the purpose for which it is intended. No liability is accepted by Draper Tools Limited for incorrect use or application of any of our products, and Draper Tools Limited cannot be held responsible for any damage to personnel, property or equipment when using this product. -
Page 6: Health And Safety Information
Warning: Please read all safety warnings and all details carefully. Failure to follow the warnings may result in serious injury or major component damage. Important: Draper Tools recommends that this product should not be modified or used for any application other than that for which it was designed. -
Page 7: Parts Drawing And Listing
CONTENTS ITEM DESCRIPTION STOCK No. 12-171/KM-813 - Crankshaft Locking Pin 21918 LRT-12-171/11.2.300 12-173/KM-6267 - Camshaft Setting Plate 21952 LRT-12-173/11.6.320 12-174/KM-6267 - Locking Clamp Assembly 22359 LRT-12-174/11.6.322 12-172/KM-823 - Loop Pin 22360 LRT-12-172/11.3.340 Flywheel Locking Pin Type 2 11.6.080 22361 Flywheel Locking Pin Type 1 11.5.180 22364 - 7 -... -
Page 8: Application
APPLICATION The 15498 has been developed as an engine timing kit for the vehicles listed below. With the camshaft locking plate in position and the crankshaft locked in a timed position it allows the user to change the timing chain or check valve timing. -
Page 9: Preparation
The following is for guidance only. Please refer to OEM derived data such as the vehicle manufacturer’s own data or Autodata. The use of this product is purely down to the user’s discretion and Draper Tools Limited cannot be held responsible for any damage caused what so ever. -
Page 10: Procedure And Application Guide
The following instructions are for guidance only. Please refer to OEM derived data such as the vehicles manufactures own data or Autodata. The use of these engine timing tools is purely down to the user’s discretion and Draper Tools cannot be held responsible for any damage caused what so ever. -
Page 11: Explanation Of Symbols
10. EXPLANATION OF SYMBOLS 10.1 EXPLANATION OF SYMBOLS Read the guide. Refer to website. - 11 -... - Page 12 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the 15498 and is the answer not in the manual?
Questions and answers