battistella PLUTONE 2009 Instruction And Maintenance
  1. Manuals
  2. Brands
  3. battistella Manuals
  4. Ironing Centers
  5. PLUTONE 2009
  6. Instruction and maintenance

battistella PLUTONE 2009 Instruction And Maintenance

Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTIONS AND MAINTENANCE
Read these directions carefully before operating.
Don't use the machine differently from the following instructions.
1.
SPECIFICATIONS
MODEL:
POWER SUPPLY:
TOTAL INSTALLED POWER:
POWER OF IRON 1:
POWER OF IRON 2:
BOILER POWER:
PUMP POWER:
BOILER CAPACITY:
IRONING ENDURANCE:
OPERATING PRESSURE:
WEIGHT:
OVERALL DIMENSIONS:
BRUSH (OPTIONAL):
MADE IN ITALY
STEAM ADJUSTMENT
KNOB
CARD ON/OFF
SWITCH
PLUTONE '09 v01
MOD. PLUTONE 2009
PLUTONE 2009
V 400 ~ + NEUTRAL / 50 Hz
W 5648
W 800
W 800
W 4000
W 48
5 L.
CONTINUOUS
4 BAR
Kg 22
30x43x98h cm
W 500
IRON CONNECT PLUG
STEAM HOSE
SOLENOID VALVE
WATER INLET
HOSE HOLDER
WATER TANK
(UPON REQUEST)
IRON
MANOMETER
IRON REST
EXHAUST TAP
Fig. 1
pag. 1
PLUTONE 2009
(Pedrollo pump)
V 400 ~ + NEUTRAL / 50 Hz
W 5970
W 800
W 800
W 4000
Hp 0,5
5 L.
CONTINUOUS
4 BAR
Kg 24
30x43x98h cm
W 500
CABLE SUPPORT
marzo 2009

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PLUTONE 2009 and is the answer not in the manual?

Questions and answers

Related Manuals for battistella PLUTONE 2009

Summary of Contents for battistella PLUTONE 2009

  • Page 1 INSTRUCTIONS AND MAINTENANCE MOD. PLUTONE 2009 Read these directions carefully before operating. Don’t use the machine differently from the following instructions. SPECIFICATIONS PLUTONE 2009 MODEL: PLUTONE 2009 (Pedrollo pump) POWER SUPPLY: V 400 ~ + NEUTRAL / 50 Hz V 400 ~ + NEUTRAL / 50 Hz...

  • Page 2: Standard Mode

    IMPORTANT Before installing PLUTONE, it is necessary to set up the following: 1. a water connection (tap with hose holder); PLUTONE will be connected to the tap with hose holder named “WATER INLET” (fig. 1) by means of a rubber hose which must have a pressure resistance of at least 10 ATM.

  • Page 3: Standby Mode

    STAND-BY MODE Key which allows access to the menu. To exit the menu SET/RESET wait for 5 seconds or press ESC. This key is used also Reset to reset warnings Key to confirm the choice made within the menu Key to exit the current function or the menu UP/DOWN Key to scroll up or down within the menu MEANING OF ICONS...

  • Page 4: Connection And Starting

    CONNECTION AND STARTING 1. Connect the rubber hose to the hose-holder indicated as WATER INLET placed on the Plutone (fig. 1) and turn the water tap on. For Plutone equipped with water tank, you just have to fill it and connect the machine to the mains supply. N.B.: make sure there is always water inside the water tank.
  • Page 5 MENU To gain access to the MENU, press the key shown on the left. To exit the MENU press ESC or wait for 5 seconds. Reset MENU: TOTAL HOURS: Cannot be zeroed To exit Zeroing of hours HOURS OF WORK PARTIAL HOURS: Reset...
  • Page 6 Password needed. Service Centre authorized access only MAINTENANCE Password needed. Manufacturer authorized access only. MANUFACTURER WARNING: AFTER 10 ATTEMPTS TO ACCESS THE “ ” OR “ ” MAINTENANCE MANUFACTURER MENU WITHOUT TYPING IN THE PASSWORD, OR EVERY TIME THE WRONG PASSWORD IS TYPED, THE MENU WILL BE BLOCKED.

  • Page 7: Electrical Risks

    4. For dry ironing it is possible to adjust the thermostat (fig. 2) on different positions according to the type of fabric (check garment label). For steam ironing you should adjust the thermostat on “cotton/flax” position. MICROSWITCH FOR IRON ELECTRICAL THERMOSTAT WIRE STEAM HOSE...
  • Page 8 WARNING:THERMIC DANGER INCANDESCENT IRON BASE  Do not iron garments directly on persons.  Do not leave hot iron on garments.  After use, always store away the iron on proper iron rest. 14. INTERVENTIONS AND SMALL REPAIRS The following procedures MUST be carried out ONLY when the boiler is cold and the plug is disconnected from the mains.
  • Page 9 WATER INLET FILTER Fig. 4 16. CLEANING OF THE BOILER PROBE To clean the probe of the boiler, do as follows: PROBE 1. open the rear panel of the machine; 2. find the boiler and the probe; 3. unscrew the probe by using a wrench and take it out; 4.

  • Page 10: Packing, Storage And Transport

    (included, without any limitation, consequential damages due to loss or no profit, cutback or any other economical loss) deriving form the use of a BATTISTELLA machine, even in case the Company had been previously informed of such kind of possibility.

Table of Contents

Save PDF