1. Manuals
  2. Brands
  3. Triton Manuals
  4. Bathroom Fixtures
  5. 2181629F
  6. Manual

Triton 2181629F Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PUSH BUTTON
Diverter Mixer
REGISTER ONLINE
ENTER A PRIZE DRAW
WIN
£100
LOVE2SHOP VOUCHERS
VISIT OUR WEBSITE TODAY
TRITONSHOWERS.CO.UK/REGISTER
PRODUCT REGISTRATION IS ONLY AVAILABLE
TO UNITS PURCHASED & INSTALLED IN THE UK
FOR YOUR SERVICE REFERENCE
NOTE DOWN THE PRODUCT CODE BELOW
(FROM THE LABEL ON THE FRONT OR TOP OF THE BOX)
ALTERNATIVELY REGISTER BY TEL: 024 7637 8321
INSTALLATION AND OPERATING INSTRUCTIONS
Please read this book thoroughly and familiarise yourself with all instructions before commencing
installation and keep it for future reference.
The mixer shower installation MUST be carried out by a suitably qualified person, in the sequence
of this instruction book.
IMPORTANT SAFETY ADVICE
The shower head and hose supplied with
this product are a safety critical part of your
shower. Failure to use genuine Triton parts may
cause injury and invalidate your guarantee.
2181629F - July 2022

Advertisement

Table of Contents
loading

Related Manuals for Triton 2181629F

Summary of Contents for Triton 2181629F

  • Page 1 (FROM THE LABEL ON THE FRONT OR TOP OF THE BOX) shower. Failure to use genuine Triton parts may cause injury and invalidate your guarantee. ALTERNATIVELY REGISTER BY TEL: 024 7637 8321...

  • Page 2: Table Of Contents

    GUARANTEE, SERVICE POLICY, ETC.......... rear cover nstallers please note these InstructIons are to be left wIth the user To check the product suitability for commercial and multiple installations, please contact Triton’s speci cation advisory service before installation. Please see back of book for contact information.

  • Page 3: Main Components

    Push button mixer shower MAIN COMPONENTS A. Mixer shower B. Riser rail C. Wall brackets D. Riser rail wall bracket E. Slider Hose (not shown) G. Shower head (not shown) H. Fixed shower head (not shown)

  • Page 4: Dimensions

    Push button mixer shower DIMENSIONS - All dimensions listed in this fitting book regarding the product and installation are approximate. 255x190mm 19mm 130x50mm 22mm 40mm 59mm...

  • Page 5: Introduction

    Push button mixer shower INTRODUCTION SAFETY WARNINGS DO NOT allow the inlet pressure or flow rates This book contains all the necessary fitting and operating instructions for your mixer shower. to operate outside the guidelines laid out in site Please read them carefully and read through requirements.

  • Page 6: Plumbing & Water System Requirements

    DO NOT connect to any form of tap or fitting have to be fitted. For advice on the scale not recommended by the manufacturer. inhibitor, please contact the Triton Customer DO NOT use jointing compounds on any pipe Experience team.

  • Page 7: Typical Domestic Installations

    Push button mixer shower TYPICAL DOMESTIC INSTALLATIONS *Diagrammatic view – not to scale. *Fig.1 For illustration purposes only. Pumped Gravity Fed Systems (fig.1) The mixer shower MUST be fed from a cold Stop valve water cistern and hot water cylinder providing Cold water Cold supply nominally equal pressures.
  • Page 8 Push button mixer shower Unvented Mains Pressure Systems *Diagrammatic view – not to scale. *Fig.3 For illustration purposes only. (fig.3) The mixer shower can be installed with an unvented, stored hot water cylinder. For systems with no cold water take off after the appliance reducing valve, it will be necessary to fit an additional drop tight pressure reducing valve when the mains pressure is over 5 bar.

  • Page 9: Preparing The Shower

    Push button mixer shower PREPARING THE SHOWER *Diagrammatic view – not to scale. *Fig.5 For illustration purposes only. Check the contents to make sure all parts are present. Before starting the installation make sure all the openings on the mixer shower are carefully covered to stop ingress of any debris while routing the supply pipework.

  • Page 10: Installation

    Push button mixer shower INSTALLATION Fig.6 STUD PARTITION OR INSTALLING THE WALL BRACKETS DRY LINED WALL PRIMARY CONSIDERATIONS Pipework through Please consider the following points before Pipework hole beginning the installation: • The brackets must be mounted onto a surface that is both solid and strong enough to support the final assembly of brackets and bar mixer.
  • Page 11 Push button mixer shower Complete the pipework to the bracket mounting Fig.9 points. Leave an excess of pipe protruding out Finished of the wall of approximately 60mm as measured wall from the face of the finished wall or tiles (fig.9). Flush the pipework through to remove any debris.
  • Page 12 Push button mixer shower Using a suitable sealant, seal the join between Fig.13 the mounting plate and the wall/tiles to prevent water entering the wall. (fig.13). Wipe away any excess sealant which may obstruct the fitting of the mixer valve. Sealant T00359 INSTALLING THE SHOWER...
  • Page 13 IMPORTANT: When installing the wall Fig.18 bracket, care must be taken not to damage the decorative surface finish. Triton recommend the use of an appropriate tool with a soft cloth, or similar, placed between the product and the tool (fig18).

  • Page 14: Leak Testing

    Push button mixer shower LEAK TESTING Fig.19 Screw the nut end the of the hose to the bottom outlet on the mixer shower, making sure that the sealing washer is in place, and direct it to waste (fig.19). Open the isolating valves to the mixer shower and check for leaks.

  • Page 15: Operating The Shower

    Push button mixer shower OPERATING THE SHOWER Fig.20 FLOW CONTROL To start the mixer, rotate the on/off flow control (fig.20). TEMPERATURE CONTROL Fig.21 To adjust the water temperature, rotate the Override button temperature control to the desired temperature (fig.21). To overcome the maximum temperature stop, press the override button and turn.

  • Page 16: Commissioning

    In either case there is no risk of scalding. If, however, the temperature is above 43°C then it is likely there is contamination in the mixer shower stopping it from shutting off the hot supply. In this case refer to the maintenance section or contact Triton Customer Experience.

  • Page 17: Adjusting The Maximum Temperature Setting

    Push button mixer shower TEMPERATURE ADJUSTMENT Fig.23 Important Adjusting the Maximum Temperature Override Setting The mixer shower has a temperature stop to prevent accidental rotation to higher Remove the temperature control by removing temperatures. This is adjustable to provide a the end cap and unscrewing the retaining screw maximum temperature of 35°C –...

  • Page 18: Maintenance

    Push button mixer shower MAINTENANCE Cleaning The manufacturer recommends that all products The following maintenance procedure is are cleaned using warm, soapy water. recommended for domestic installations but must be carried out for commercial installations. Do not use abrasive or aggressive chemical cleaning products as this may affect the product Maintenance of the mixer shower is required to surface finish and invalidate your guarantee.

  • Page 19: Flow Rates

    Push button mixer shower PRODUCT FLOW RATES - For guidance only Hand held shower head 11.5 14.0 16.5 18.0 flow rate (l/m) Overhead showe head flow 12.0 15.0 17.0 18.5 rate (l/m) Pressure (bar) Conditions for test Inlet temperatures comply with EN1111 requirements. Outlet temperature 38C.

  • Page 20: Fault Finding

    1.4 Cold water supply 1.4.1 Turn off the mixer shower and consult blocked. a competent plumber or contact Triton Customer Experience. 1.5 High volume of cold 1.5.1 Reduce the simultaneous demand from the water drawn off supply.
  • Page 21 Push button mixer shower FAULT FINDING Problem Cause Action 4 Water does not 4.1 Water supplies cut off. 4.1.1 Check water elsewhere in house and if flow or shower necessary contact local water company. pattern collapses 4.2 Mixer shower 4.2.1 Inspect the inlet filters. Clean if necessary. when another blocked.
  • Page 22 Push button mixer shower...
  • Page 23 Push button mixer shower...
  • Page 24 Trade Installer Hotline: 024 7637 8344 Nuneaton www.tritonshowers.co.uk Warwickshire, CV11 4NR E-mail: serviceenquiries@tritonshowers.co.uk E-mail: technical@tritonshowers.co.uk Triton is a division of Norcros Group (Holdings) Limited Triton reserve the right to change product specifi cation without prior notice. E&OE. © TRITON SHOWERS 2022...

Table of Contents