Table of Contents
Advertisement
SENSING CHARACTERISTICS (TYPICAL)
SH-61R
Parallel deviation
4
13.123
3
9.843
2
6.562
Receiver
1
3.281
L
Emitter
0
400
200
0
200
400
15.748
7.874
7.874
15.748
Left
Center
Right
Operating point (mm in)
PRECAUTIONS FOR PROPER USE
Sensor head
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
• Always use the sensor head and the exclusive amplifier
together as a set.
Mounting
Ultra-slim type
• With tapped screws
<Side sensing>
Sensing
7.5
direction
0.295
Attached
mounting
screws
M2 × 0.4
0.016
holes,
tapped 6
0.236
deep
[M2 (length 8 mm
0.315
in)]
The tightening torque should be 0.14 N·m or less.
• With attached screws and nuts
<Side sensing>
Plain washers
7.5
Attached
mounting
0.295
screws
[M2 (length 8 mm
Spring washers
0.315
in)]
Mounting board thickness:
Mounting board thickness:
1.5 mm
0.059 in
or less
3 mm
0.118 in
The tightening torque should be 0.14N·m or less.
Slim Body Automatic Sensitivity Setting Photoelectric Sensor
Sensing field with optional mounting bracket (MS-SH6-2)
Horizontal &
vertical directions
100
3.937
Sensor
Horizontal
head
direction
50
1.969
Vertical
direction
White non-
glossy paper
0
40
20
0
20
1.575
0.787
0.787
(Down) Left
Center
Right (Up)
Operating point (mm in)
<Front sensing>
Sensing
direction
Attached
7.5
mounting
0.295
screws
[M2 (length 8 mm
0.315
in)]
M2 × 0.4
0.016
holes,
(Unit: mm in)
tapped 7
0.276
deep
<Front sensing>
Nuts
Attached
mounting
7.5
screws
0.295
[M2 (length 8 mm
0.315
in)]
or less
(Unit: mm in)
SU-7
40
1.575
For ultra-small type, mark sensor & glass substrate detection sensor
• The tightening torque should be 0.29 N·m or less when
mounting the sensor head with the screws.
Chemical resistant type
• Use M3 screws to mount the sensor head with the
attached sensor head mounting bracket.
20 mm
0.787 in
• Use M4 screws to assemble the sensor head with the
optional sensor head mounting bracket MS-SH6-2, in
order to form the convergent sensing mode.
In case of chemical resistant type sensor head
• Do not use where it can be exposed to molten alkali
metals (sodium, potassium, lithium, etc.), fluorine gas
(F
), CIF
, OF
(including gaseous state), etc.
2
3
2
• In case of cable extension, the extended portion
should be placed in an area where it is not exposed to
chemicals.
SH
SERIES
SERIES
Chemical resistant type
M3 (length 12 mm
0.472
in) screws
with washers
Sensor head
mounting bracket
MS-SS3-1
(Optional)
M3 screws [Material: Stainless steel (SUS304)]
(Purchase separately.)
Sensor head mounting bracket
MS-SH6-1 (Accessory)
[Material: Stainless steel (SUS304)]
M4 screws [Material: Stainless steel (SUS304)]
(Purchase separately.)
Sensor head mounting bracket
MS-SH6-2 (Optional)
[Material: Stainless steel (SUS304)]
11
Advertisement
Table of Contents
