Precautions For Proper Use; Sensor Head - Panasonic SU-7 Series Manual

SENSING CHARACTERISTICS (TYPICAL)
SH-61R
Parallel deviation
4
13.123
3
9.843
2
6.562
1
3.281
0
400 200 0
15.748 7.874
Left Center
Operating point (mm in)

PRECAUTIONS FOR PROPER USE

Sensor head

• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
• Always use the sensor head and the exclusive amplifier
together as a set.
Mounting
Ultra-slim type
• With tapped screws
<Side sensing>
Sensing
direction
Attached
mounting
screws
[M2 (length 8 mm
0.315 in)]
The tightening torque should be 0.14 N·m or less.
• With attached screws and nuts
<Side sensing>
7.5 Attached
mounting
0.295
screws
[M2 (length 8 mm
0.315 in)]
Mounting board thickness:
1.5 mm 0.059 in or less
The tightening torque should be 0.14N·m or less.
Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com.
Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from
Slim Body Automatic Sensitivity Setting Photoelectric Sensor
Sensing field with optional mounting bracket (MS-SH6-2)
Horizontal &
vertical directions
100
3.937
Sensor
Horizontal head
direction
50
1.969 Vertical
direction
Receiver
White non-
L
glossy paper
Emitter
0
200 400 40 20
7.874 15.748 1.575 0.787
Right
(Down) Left Center
Operating point (mm in)
<Front sensing>
Sensing
direction
7.5
0.295
Attached
mounting
screws
M2 × 0.4 0.016 holes,
[M2 (length 8 mm
tapped 6 0.236 deep
0.315 in)]
M2 × 0.4 0.016 holes,
tapped 7 0.276 deep
<Front sensing>
Plain washers
Nuts
Attached
mounting
screws
Spring washers
[M2 (length 8 mm
0.315 in)]
Mounting board thickness:
3 mm 0.118 in or less
0 20 40
0.787 1.575
Right (Up)
For ultra-small type, mark sensor & glass substrate detection sensor
• The tightening torque should be 0.29 N·m or less when
mounting the sensor head with the screws.
Chemical resistant type
• Use M3 screws to mount the sensor head with the
attached sensor head mounting bracket.
7.5
0.295
20 mm
0.787 in
(Unit: mm in)
• Use M4 screws to assemble the sensor head with the
optional sensor head mounting bracket MS-SH6-2, in
order to form the convergent sensing mode.
7.5
0.295
(Unit: mm in)
In case of chemical resistant type sensor head
• Do not use where it can be exposed to molten alkali
metals (sodium, potassium, lithium, etc.), fluorine gas
(F ), CIF
2
• In case of cable extension, the extended portion
should be placed in an area where it is not exposed to
chemicals.
SU-7
SERIES
Chemical resistant type
M3 (length 12 mm
0.472 in) screws
with washers
M3 screws [Material: Stainless steel (SUS304)]
(Purchase separately.)
Sensor head mounting bracket
MS-SH6-1 (Accessory)
[Material: Stainless steel (SUS304)]
M4 screws [Material: Stainless steel (SUS304)]
(Purchase separately.)
Sensor head mounting bracket
MS-SH6-2 (Optional)
[Material: Stainless steel (SUS304)]
, OF (including gaseous state), etc.
3 2
11
SH
SERIES
Sensor head
mounting bracket
MS-SS3-1
(Optional)