Table of Contents
Advertisement
SPECIFICATIONS
Sensor heads
Chemical resistant type
Type
Item
Model No.
Applicable amplifiers
5 to 80 mm
when mounted on optional
mounting bracket (MS-SH6-2) and
Sensing range
used as convergent reflective type
(Conv. point: 25 mm
0.984
Min. ø5 mm
opaque object
Min. ø1 mm
when mounted on optional
mounting bracket (MS-SH6-2) and
Sensing object
used as convergent reflective type
15 % or less of operation distance
when mounted on optional
Hysteresis
mounting bracket (MS-SH6-2) and
used as convergent reflective type.
(Note 3)
0.1 mm
0.1 mm
distance when mounted on optional
Repeatability
mounting bracket (MS-SH6-2) and
(perpendicular to sensing axis)
used as convergent reflective type.
lights up when the sensing
Operation indicator
output of the amplifier is ON,
incorporated on the emitter
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
Vibration resistance
10 to 500 Hz frequency, 3 mm
Shock resistance
Emitting element
Peak emission wavelength
Enclosure: Fluorine resin
Material
Cable sheath: Fluorine resin
Cable
0.089 mm
Cable extension
Emitter: 15 g approx.
Net weight
Receiver: 15 g approx.
MS-SH6-1(Sensor head
Accessory
mounting bracket): 2 pcs.
Notes: 1) Where measurement conditions have not been specified precisely, the
conditions used were an ambient temperature of +23 °C
2) The sensing range and the hysteresis of the mark sensor are
specified for white non-glossy paper (50 × 50 mm
in) as the object.
3) The sensing range and the hysteresis for the chemical resistant type
sensor used in the convergent reflective mode is specified for white
non-glossy paper (150 × 150 mm
4) Make sure to confirm detection with an actual sensor before use.
5) The optimum sensitivity stands for the sensitivity level when the
operation indicator just lights up in the light received condition.
Slim Body Automatic Sensitivity Setting Photoelectric Sensor
Thru-beam
Red LED
SH-61R
SH-82R
2.5 m
8.202 ft
0.197 to 3.150 in
10 to 14 mm
0.394 to 0.551 in
(Convergent point: 12 mm
(Spot diameter: ø0.7 mm
(Note 2)
in) (Note 3)
ø0.197 in
Min. 0.07 mm
width black line on
ø0.039 in
steel wire
white paper
with 12 mm
0.472 in
setting distance and at
with 25 mm
0.984 in
the optimum sensitivity
setting distance and
(Note 5)
at the max. sensitivity
–
0.004 in
or less
0.004 in
or less of operation
0.02 mm
0.0008 in
or less
with 25 mm
0.984 in
setting
distance and at the optimum
sensitivity (Note 5)
Orange LED
(lights up when the sensing output of the amplifier is ON)
IP67 (IEC)
–10 to +55 °C
+14 to +131 °F
Storage: –20 to +70 °C
Incandescent light: 3,500 ℓx or less (SH-61R: 2,000 ℓx or less) at the light-receiving face
0.118 in
double amplitude (SH-72: 10 to 55 Hz frequency, 1.5 mm
500 m/s
acceleration (50 G approx.) in X, Y and Z directions three times each
2
Red LED (modulated)
644 nm
0.025 mil
680 nm
0.027 mil
single core, two parallel (SH-61R: 0.089 mm
2
Extension up to total 5 m
16.404 ft
+73.4
°F.
1.969 × 1.969
5.906 × 5.906
in) as the object.
Mark sensor
Pinpoint
Green LED
SH-82G
SU-7 series
10 to 14 mm
0.394 to 0.551 in
0.472
in)
(Convergent point: 12 mm
0.472
in)
ø0.028
in)
(Spot diameter: ø1 mm
ø0.039
in)
(Note 2)
0.003 in
Min. 0.2 mm
0.008 in
width black line on
white paper
with 12 mm
0.472 in
setting distance and at
the optimum sensitivity
(Note 5)
10 % or less of operation distance (Note 2)
0.03 mm
0.001 in
or less
Red LED
–
(No dew condensation or icing allowed),
–4 to +158 °F
35 to 85 % RH, Storage: 35 to 85 % RH
Green LED (modulated)
570 nm
0.022 mil
Enclosure: Polycarbonate, Lens: Acrylic
single core) shielded cables, 2 m
2
is possible with an equivalent cable (SH-61R: both emitter and receiver).
20 g approx.
–
6) The minimum sensing object for SH-84R is specified for the case when
the sensor detects a black line with respect to the spot as shown below.
Spot
7) The repeatability for SH-84R is specified for the case when the sensing
object approaches the spot sideways as shown below (0.12 mm
if it approaches from above or below).
Spot
SU-7
SH
SERIES
SERIES
Glass substrate
detection sensor
Line-focus
SH-84R
SH-72
17 to 23 mm
0.669 to 0.906 in
0.5 to 7.5 mm
(Convergent point:20 mm
0.787
in)
with transparent
(Spot size: 1 × 4 mm
0.039 × 0.157
in)
glass plate
(Note 2)
Min. 0.07 mm
0.003 in
width black line on
□24 mm
□0.945 in
white paper (Note 6)
more transparent glass,
with 20 mm
0.787 in
aluminum-evaporated
setting distance and at
mirror, etc. (Note 4)
the optimum sensitivity
(Note 5)
5 % or less of operation
distance
0.03 mm
0.03 mm
0.001 in
0.001 in
or less
or less
(Note 7)
(along sensing axis)
–
–10 to +60 °C
No dew condensation
or icing allowed
Storage: –10 to +60 °C
0.059 in
amplitude) in X, Y and Z directions for two hours each
Red LED (modulated)
Infrared LED (modulated)
680 nm
0.027 mil
880 nm
Enclosure: Polycarbonate
6.562 ft
long (SH-72: 3 m
25 g approx.
Black line
Sensing
object
7
0.020 to 0.295 in
or
+14 to +140 °F
+14 to +140 °F
0.035 mil
9.843 ft
long)
0.005 in
Advertisement
Table of Contents
