Delta DNPS01 Instruction Sheet

Warning
This instruction will be helpful in the installation, electronic specification, function specification and
troubleshooting of the DVPPS01 and DVPPS02.
This is an OPEN TYPE DVPPS series. The DVPPS series should be kept in an enclosure away from airborne dust,
high humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special
tools or keys to open the enclosure, so as to avoid the hazard to users and the damage to the DVPPS series.
Never connect the AC main circuit power supply to any of the output terminals, as it will damage the DVPPS series.
Check all the wiring prior to power up. To avoid any electromagnetic noise, make sure the DVPPS series is properly
grounded .
Introduction
Thank you for choosing DELTA DVP series. DVPPS series is a power module with 2 types that sorted by output
circuit. 1. DVPPS01 provides 24V DC and 1A current for output power. 2. DVPPS02 provides 24V DC and 2A
current for output power. DVPPS series is only used for Delta DVP series. DVPPS series is separated from the
PLC MPU for better space utilization and easier installation.
Product Profile & Outline
DVPPS01
2
D V PP S01
5
4
1
13.3 60
36.5
3
3
6
Unit: mm
1 Power LED
2 Output/input terminal (fixed terminal)
3
DIN rail clip
4
DIN rail track (35mm)
Electrical Specifications
Model
DVPPS01
Item
Power input 100 ~ 240VAC (-15% ~ +10%), 50/60Hz
Output power 24VDC (±3%), output current: 1A max.
Ripple & noise Under 100mV Typical at full load
p-p
Efficiency 78% ~ 87% Typical at full load
Over load/short circuit
Auto Recovery
protection
The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and
Grounding
N (All PLC units should be grounded directly to the ground pole).
Operation/storage Operation: 0° C ~ 55° C (temperature), 50 ~ 95% (humidity), Pollution degree 2;
environment Storage: -25° C ~ 70° C (temperature), 5 ~ 95% (humidity)
Underwriters Laboratories, Inc.: UL508 Listed (Industrial Control Equipment)
Agency approvals
European Community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC
Weight (g) 158
DVPPS02
7
55 13.3 60
2
5 DVPPS02
1
32.5
7
3
Unit: mm
5 I/O terminal label
6 Nameplate
7
Mounting holes
DVPPS02
100 ~ 240VAC (-15% ~ +10%), 50/60Hz
24VDC (±3%), output current: 2A max.
Under 240mV Typical at full load
p-p
250
Installation and Wiring
Mounting Arrangements and Wiring
DIN Rail Installation:
The DVPPS can be secured to a cabinet by using the DIN rail that
is 35mm high with a depth of 7.5mm. When mounting the DVPPS
on the DIN rail, be sure to use the end bracket to stop any
side-to-side motion of the DVPPS, thus to reduce the chance of
the wires being pulled loose. On the bottom of the DVPPS is a
small retaining clip. To secure the DVPPS to the DIN rail, place it
onto the rail and gently push up on the clip. To remove it, pull
down on the retaining clip and gently pull the DVPPS away from
the DIN rail. Please see the figure on the right:
Direct mounting: Tighten M4 screws into direct mount hole.
Wiring:
Below 6.2
To suit M3.5 screw terminals
Below 6.2
Wiring Notes
Environment
1. DO NOT store the DVPPS01/DVPPS02 in a dusty, smoky, or corrosive atmosphere.
2. DO NOT store the DVPPS01/DVPPS02 in an environment with high temperature or high humidity.
3. DO NOT install PLC on a shelf or on an unstable surface.
Power Input Wiring
Power input of DVPPS01/DVPPS02 is AC input; following items should be noticed:
1. Connect the AC input (100VAC ~ 240VAC) to terminals L and N. Any 110VAC or 220VAC connected to the
+24V terminal will permanently damage the DVPPS01/DVPPS02.
2. Please use wires of 1.6mm and above for the grounding.
3. If the power-cut time is less than 10ms, the DVPPS01/DVPPS02 still operates unaffectedly. If the
power-cut time is too long, the DVPPS01/DVPPS02 will stop operating and all the outputs will be Off.
Trial Run
Power indicator, Running and Test
The "POWER" LED at the front of DVPPS01/DVPPS02 will be lit (in green) if the power is on. If the indicator
is not ON, it indicates that the power supply is not enough or short circuit. Please check your power wiring.
Troubleshooting
Judge the errors by the indicators on the front panel. When errors occurred on DVPPS01/DVPPS02, please
check:
"POWER" LED
The "POWER" LED at the front of the MPU will be lit (in green) if the power is on. If the indicator is not on
when the MPU is powered up, please check if power supply is normal. If the indicator is not on when the MPU
is powered up and with the input power being normal, it is an indication that the PLC is malfunction. Please
have this machine replaced or have it repaired at a dealer near you.
注 意 事 項
ENGLISH
(OPEN TYPE)
產 品 簡 介
DVP
24V DC 1A
產 品 外 觀
DVPPS01
2
D VPPS01
5
1
4
36.5
3
3
6
1
2
/
3
DIN
4
DIN
電 氣 規 格
機 種
項 目
輸 入 電 源 100 ~ 240VAC (-15% ~ +10%), 50/60Hz
輸 出 電 源 24VDC (±3%),
漣 波 & 雜 訊 滿 載 條 件 下 小 於
效 率 滿 載 條 件 下
過 載 / 短 路 保 護 自 動 恢 復
接 地 接 地 配 線 之 線 徑 不 得 小 於 電 源 端
儲 存 環 境 操 作 ：
操 作
/
儲 存 ：
美 國 安 全 檢 測 實 驗 室 公 司
安 規 認 証
歐 洲 電 磁 相 容 性 指 令
質 量 ( 約 , g) 158
1. Please use O-type or Y-type terminals for I/O wiring terminals. The specification
for the terminals is as shown on the left. Tighten PLC terminal screws to a torque
of 5 ~ 8kg-cm (4.3 ~ 6.9 in-lbs).
2. Please avoid tiny metal material enter DVPPS01/DVPPS02 when screwing and
wiring. After finishing wire, remove the affix that pasted on the heat sink for heat
dissipation.
3. Use Copper Conductors Only, 60°C.
( :
/
DVPPS
2. DVPPS02 24V DC 2A
DVPPS02
7
5
4
13.3 60
3
3
6
mm
5
6
( )
7
(35mm)
DVPPS01
100 ~ 240VAC (-15% ~ +10%), 50/60Hz
最 大 輸 出 電 流 : 1A 24VDC (±3%),
100mV 滿 載 條 件 下 小 於
p-p
78% ~ 87%
之 線 徑 （ 多 台
L, N PLC
0 °C ~ 55°C （ 溫 度 ） ， 5 0 ~ 95% （ 濕 度 ） ， 污 染 等 級
- 25°C ~ 70°C （ 溫 度 ） ， 5 ~ 95% （ 濕 度 ）
: UL508 Listed (Industrial Control Equipment)
89/336/EEC 和 低 電 壓 指 令 73/23/EEC
250
For heat dissipation. Make
sure to provide a minimum
clearance of 50mm
between the unit and all
sides of the cabinet. (as
shown below)
> 50mm
DVP MPU
> 50mm > 50mm
> 50mm
繁 體 中 文
/
)
2 1. DVPPS01
DVPPS DVP
55 13.3 60
2
DV PPS0 2
4
1
32.5
7
3
6
mm
/
DVPPS02
最 大 輸 出 電 流 : 2A
240mV
p-p
同 時 使 用 時 ， 請 務 必 單 點 接 地 ）
2 ；