Table of Contents
Advertisement
- Clean the parts with detergent, water and a suitable
utensil, rinse and dry.
2
- Make sure when reassembling the parts that they are
slotted in correctly.
WARNING
Every time a replacement involving gas input parts is
made, recheck all functions and test for leakage.
HOW TO REPLACE COMPONENTS
Use only original spare parts supplied by the manufacturer.
All maintenance must be carried out by qualified
personnel. The appliance should be serviced at least
once a year, which is why we recommend signing our
maintenance agreement.
To replace the following pieces, firstly remove the control
knobs and the control panel (after having loosened the
fixing screws( as well as any other necessary panel.
Cock with safety valve for open flame and hotplate
"Fullplate" burners - (Fig. 2)
Loosen the gas pipe and thermocouple fitting, loosen
the fitting which fixes the cock to the pipe and replace
the piece.
Thermocouple (for open flame or hotplate "Fullplate"
burners)
Loosen the nuts fixing the thermocouple to the valve and
the burner and replace the piece.
Thermostat valve tap on the gas oven (Fig. 3)
Loosen the nuts of the gas ducts and of the thermocouple,
remove the thermostat bulb from the supporting clips
located inside the oven chamber and replace with the
new cock.
Oven thermocouple
Remove the floor, unscrew the nut on the tap and the
burner and replace the thermocouple.
Replacing the heating elements of electric ovens
Disconnect the switch upstream of the appliance so that
the unit will be disconnected from the mains. In the FE
oven, the lower heating elements are positioned under the
bottom and the upper heating elements are positioned on
the upper side of the cooking chamber. In the FE1 oven,
the heating element is positioned behind the conveyor on
the rear of the cooking chamber. To remove the heating
elements, loosen the screws fixing them; pay attention
to the connection leads. Use a screwdriver to disconnect
the connection leads and mount a new heating element
following the sequence in reverse.
USING THE APPLIANCE
Turning a gas-ring burner on and off (Fig. 2)
Turn knob (21( to the left until the spark position.
(SPARE PARTS)
START-UP
MOD.
Qn
V
Light the pilot burner using a match or other suitable
means. Keep the knob pressed down while repeatedly
pressing the piezoelectric ignition button until the flame is
lit. Then turn the knob to the high or low flame position in
order to light the main burner of the corresponding ring.
To turn off the burner, turn the knob to the right until the
spark position and the main burner will go out. To turn
off the pilot burner turn the knob to the off position
The flame can be adjusted:
to maximum capacity
to minimum capacity
Start-up and shutdown of the fullplate
Push and turn knob (21( to the left until the spark position
and at the same time press the push button marked
Keep the knob pressed down while repeatedly pressing
the piezoelectric ignition button until the flame is lit. Then
turn the knob to the high or low flame position in order to
light the main burner of the corresponding ring. To turn
off the burner, turn the knob to the right until the spark
position and the main burner will go out. To turn off the
pilot burner turn the knob to the off position
Turn-on and turn-off of gas oven without pilot flame –
(FG1 Oven) (Fig. 3)
Turn-on: open the oven door, press and turn the knob and,
while keeping it pressed, use a flame to turnon the oven
at position M. Keep the knob pressed down for about 20"
after ignition, so that the safety device activates. Now
adjust the thermostat setting to the one most suitable for
the chosen cooking method.
Turn-on and turn-off of gas oven with pilot flame (FG
Oven and Tuttoforno T - Fig. 5)
Turn on: open the oven door, press and turn the knob to
position
and keep it pressed while lighting the pilot
light with the piezoelectric lighter or a match.
This operation may be observed through the hole in the
oven floor. Keep the knob pressed down for about 20"
after ignition, so that the safety device activates.
Then adjust the thermostatic setting according to the
MOD.
N°:
cooking programme required.
Qn
V
kW:
Hz: 50/60
IPX2
OPERATING INSTRUCTIONS FOR ELECTRIC OVEN
Turn-on and turn-off of the FE type electric oven (fig. 6)
By turning the selector switch (23( to the left or the right,
you can choose the type of cooking, heat above and/
or below. In either of these positions the green light
comes on (25 = live appliance(. By turning the selector
switch (24( on desidered position, resistances are switched
on warning light (26( comes on and goes off when
the selected temperature is reached and the resistances
switch off. To turn the oven off, turn the thermostat into
position
and the selector into position
Turn-on and turn-off of the FE1 and FE2 type electric
oven (fig. 8)
In this type of oven the heat comes from the rear of
the chamber; it is, however, equipped with a fan which
N°:
MOD.
Qn
kW:
Hz: 50/60
IPX2
V
kW:
| 119
(large flame(
(small flame(
MOD.
N°:
Qn
V
kW:
Hz: 50/60
IPX2
.
MOD.
N°:
Qn
V
kW:
Hz: 50/60
IPX2
.
N°:
Hz: 50/60
IPX2
.
.
EN
Advertisement
Table of Contents
