Flex ST 1005 VE Operating Instructions Manual page 12

Safety instructions
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can be attached
to your power tool, it does not assure safe
operation.
 Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
If appropriate, wear a dust mask, hearing
protection, protective gloves and/or
a special apron which protect you from
small sanding and material particles.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must
be capable of filtrating particles generated by
your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
 Hold power tool by insulated gripping
surfaces only, when performing an opera-
tion where the cutting accessory may
contact hidden wiring or its own cord.
Contact with a live cable may also cause
metal parts of the power tool to become
live and result in an electric shock.
 Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
12
 Do not run the power tool while carrying
it at your side.
Accidental contact with the spinning acces-
sory could snag your clothing, pulling the
accessory into your body.
 Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside
the housing and excessive accumulation
of powdered metal may cause electrical
hazards.
 Do not operate the power tool near
flammable materials.
Sparks could ignite these materials.
`^rqflk>
eÉ~äíÜ=êáëâ=Ñêçã=áåÜ~äáåÖ=íçñáÅ=Çìëí=ÅçåëáëíáåÖ=
çÑ=ãÉí~äI=ïççÇ=çê=äÉ~ÇJÄ~ëÉÇ=é~áåíK
 It is not recommended to sand lead paint.
Lead paint should be removed by a specia-
list only.
 Do not work on materials which release
hazardous substances (e.g. asbestos).
Take precautions if hazardous, combustible
or explosive dust is likely to occur.
Wear protective dust mask.
Use dust extraction system.
 When working, hold the electric power tool
firmly with both hands and ensure that you
have a secure footing. The electric power
tool is controlled more securely if held with
both hands.
 Do not use the electric power tool if it has
a damaged power cord. Do not touch the
damaged power cord and pull out the mains
plug if the power cord is damaged during
work. Damaged power cords increase
the risk of an electric shock.
a^j^db=ql=molmboqv>
 The mains voltage and the voltage
specifications on the rating plate must
correspond.
ST 1005 VE