Page 2
To the Holder of this Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice. In no event will ADTRAN be liable for any special, incidental, or consequential damages or for commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Page 6
Advance notification and the opportunity to maintain uninterrupted service are given. 4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the network until the problem is corrected or it is certain the equipment is not malfunctioning.
Page 9
NetVanta 5305 Hardware Installation Guide Product Warranty ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. Product Registration Registering your product helps ensure complete customer satisfaction.
Page 10
Your reseller should serve as the first point of contact for support. If additional support is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, updated firmware releases, latest product documentation, service request ticket generation and trouble-shooting tools.
NetVanta 5305 Hardware Installation Guide TABLE OF CONTENTS 1. Introduction to the NetVanta 5305 Solution ..............13 Features and Specifications .................... 13 Unpack and Inspect the System ..................14 Contents of ADTRAN Shipments ................14 2. Product Overview ......................... 15 Reviewing the Chassis Front Panel Design ..............
Hardware Installation Guide INTRODUCTION TO THE NETVANTA 5305 SOLUTION The NetVanta 5305 is a modular multi-service access router designed for corporate office connectivity over frame relay or point-to-point (PPP) networks. The NetVanta 5305 has six modular slots for customizing solutions and runs with the ADTRAN Operating System (ADTRAN OS).
NetVanta 5305 Unpack and Inspect the System Each NetVanta 5305 unit is shipped in its own cardboard shipping carton. Open the carton carefully, and avoid deep penetration into the carton with sharp objects. After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit, immediately file a claim with the carrier and contact ADTRAN Customer Service (see Product Warranty, on page 9).
Hardware Installation Guide NetVanta 5305 Front Panel LEDs Table 1 describes the front panel LEDs in order as located on the chassis from left to right. Table 1. NetVanta 5305 LEDs For these LEDs… This activity… Indicates that… STATUS Green (blinking) Unit is powering up.
NetVanta 5305 Hardware Installation Guide Reviewing the Chassis Rear Panel Design Figure 2 shows the NetVanta 5305 rear panel. Pinouts for the connectors are given in Appendix A. CAUTION: REMOVE POWER CORD PRIOR TO REMOVAL OF POWER SUPPLY 85-130VAC/190-250VAC 4A/2A 50/60Hz Figure 2.
NetVanta 5305 Controller The NetVanta 5305 uses a central Controller card to provide configuration for the system using the ADTRAN AOS. The NetVanta 5305 Controller (shown in Figure 3) provides control interfaces for the NetVanta 5305 system including a port (DB-9) and two Ethernet interfaces (RJ-48).
NetVanta 5305 T3 Wide Module (P/N 1200832L1) The NetVanta 5305 T3 Wide Module (shown in Figure 4) provides a T3 interface with a dual BNC for the NetVanta 5305. The T3 connection provides a full unchannelized T3 interface that provides a connection to the Wide Area Network.
NetVanta HSSI Wide Module (P/N 1200934L1) The NetVanta 5305 HSSI Wide Module (shown in Figure 5) provides a HSSI interface for the NetVanta 5305. Up to two HSSI Wide Modules may be used simultaneously in the NetVanta 5305 chassis. The HSSI Wide Module may be installed in any slot (1-6).
These interfaces can be used independently or as aggregate bandwidth using Multi-Link PPP protocol. Up to six T1/E1 Wide Modules may be used simultaneously in the NetVanta 5305 chassis. The T1/E1 Wide Module may be installed in any slot (1-6). Table C on page 28 gives the pinout for this module.
Installing the NetVanta VPN Accelerator Card (4200368L3) section on page 25 For information on configuring a specific application, refer to the quick configuration documents provided on your ADTRAN OS Documentation CD. For details on the command line interface, refer to the AOS Command Reference Guide (also included on the CD).
Figure 7. Rack Mounting the NetVanta 5305 Rack Mounting NetVanta 5305 The NetVanta 5305 can be rack mounted in a 19" equipment rack using the mounting kit included with the shipment. Rack mount adapter kits (P/N 12007271L1) can be purchased separately for installation in a standard 23”...
Instructions for Installing Modules Step Action Remove the cover plate from the appropriate option slot of the NetVanta 5305 rear panel using a Phillips screwdriver. Slide the option module into the slot until the module is firmly seated against the front of the chassis.
Supplying Power to the Unit As shipped, NetVanta 5305 is set to factory default conditions. After installing the chassis and any option modules, the system is ready for power-up. To power-up the system, ensure that the unit is properly connected to an appropriate power source (as outlined in the sections which follow).