Page 2
Installation Manual This manual covers the electrical and mechanical installation procedure for the Tellus TP-EVPD-30kW charger. The operations and programming manual are separate. The model hosts different voltage and connector configurations. Below are different product numbers. TP5-30-480-1 Max Voltage: 1000VDC; Connectors: CCS1 TP5-30-480-2 Max Voltage: 1000VDC;...
Installation Manual 1. CRITICAL SAFETY READ THE ENTIRE MANUAL BEFORE DESIGNING OR INSTALLING EQUIPMENT This unit is a high-powered electrical device and can be hazardous if improperly installed, serviced, or operated. Failure to follow procedures in this manual could result in extreme hazard to personnel and/or damage to the equipment and related infrastructure.
(1 to 2 minutes) with high voltage power, even after main power is disconnected. Always test with a voltmeter before any maintenance or service is performed. This manual covers the electrical and mechanical installation procedure for the Tellus TP-EVPD-30kW charger. BlinkCharging.com (888) 998.2546...
Page 6
Installation Manual SPECIFICATIONS Product # TP5-30-480 Input 480VAC (3P+N+PE), 60Hz FLA || Breaker 40A || 63A Output Voltage 150 to 1000VDC Output Current 0 to 100A CCS1 Connector(s) Dual CCS1 Efficiency ≥94% at nominal output power Power Factor > 0.98 Operating Temperature 22°F to 131°F (-30°C to 55°C) Working || Storage humidity...
Installation Manual 3. INSTALLATION OVERVIEW Input voltage: 480 VAC (3 Phase + Neutral + Earth), 60Hz Electrical Input Requirements Full Load Amperage: 40 Amps (At Rated power) Breaker Capacity: 63 Amps The charger can be installed on any stable wall or any pole structure with appropriate brackets.
Installation Manual 4. OUTLINE OF DRAWING TP-30-480 DCFC Charger Depicted to be mounted on a stand. The dimension of the bracket remains the same from wall mount and stand mount (units of measure in mm). BlinkCharging.com (888) 998.2546 •...
Installation Manual 5. STATION ANATOMY Screen Encrypted RFID Reader Touchscreen display provides An RFID reader that identifies EV real-time instructions and feedback drivers by placing their RFID card to EV drivers about services on the pad available, payment options, and any errors Emergency Stop Button DCFC Cord Mount...
Installation Manual 6. CHARGER INSTALLATION PLACING CHARGER ON THE WALL A forklift will be required to move the charger into position. The charger with the crate will weigh around 240lbs. The charger without the crate weighs around 175 lbs. To lift the charger, use the forklift cut-outs in the lower frame of the charger.
Page 11
Installation Manual CHARGER MOUNTING 1. Hold the installation bracket against the wall. 2. Make sure that the bracket is levelled. Use the spirit level to ensure. 3. Mark the location for the mounting holes. 4. Drill the mounting holes as per the template provided. 5.
Page 12
Installation Manual AC INPUT POWER WIRING INPUT VOLTAGE The Charger requires an Input voltage of 480 VAC (3 Phase + Neutral + Earth), 60Hz and current of 40 Amps. Schematic diagram of the input connection of the charger. AC INPUT TERMINATION MAIN BREAKER ABC are the 3 Phase Lines N is the Neutral.
Installation Manual 7. OPERATING INSTRUCTIONS The Tellus Power Green charger provides multiple options to operate and charge the EV. All the Tellus chargers come with a standard RFID card reader, Smart charging facility and optional Credit Card reader. Below is the screen giving various options displayed.
Installation Manual 8. HOW TO START A CHARGING SESSION RFID CARD 1. Please select the connector compatible to your EV 2. Plugin the connector, and for CHAdeMO press the “Please to Connect CHAdeMO”. 3. Charger display will show “Please swipe the card”. 4.
Installation Manual 9. CHARGER SETTINGS PARAMETER VALUE SETTING PARAMETERS TIME ZONE UTC+HH:MM During the initial installation, the setting parameters must PSM QUANTITY be set by the manufacturer or the operating partner, or the POWER OUT MODE service partner. Changes may only be made by trained OCCUPIED PLUG specialist personnel.
Installation Manual /dev/ttyS4 Path - DO NOT CHANGE LCM ENCODE TYPE UNICODE Encode - DO NOT CHANGE LCM PASSWORD 123456 Password for access RFID RFID0=/dev/ttyS1 Path - DO NOT CHANGE PLUG1 GBTDC1:2=/dev/ttyS0 Path - DO NOT CHANGE PLUG2 GBTDC2:2=/dev/ttyS0 Path - DO NOT CHANGE DC1QRCODE NAME RFID ORIGINAL NUMBER 10.
Installation Manual using a vacuum cleaner or air blower. The cabinet can be cleaned using a vacuum cleaner. The dust on the components can be cleaned using a soft cloth. Please pay extra attention while using the vacuum cleaner, it should not apply pressure on the control boards or any components.
Installation Manual SOLUTION FAULT TYPE IP address communication failure or Server Communication Check the SPD and GFCI circuit Failure The insulation check on the EV has failed. Please try to charge AC input over voltage / under voltage different EV. Please check the connection between the IM and CM boards.
Installation Manual 13. WARRANTY Warranty and Service Plan Tellus DC chargers comes with the 2 years parts only standard warranty. However, we offer service plans which covers parts and labor as well for an additional add-on fee. We can train your operators or engineers and equip with basic understanding of the troubleshooting and part replacement to make sure the equipment downtime as well as total cost of ownership is minimized.
Installation Manual Tellus disclaims any liability for damage to product, property, or personal injury resulting in whole or in • part, from improper installation, maintenance or use that is not in accordance with Tellus installation and maintenance procedures. Maintenance or use that is not in accordance with Tellus installation and maintenance procedures. •...