Advertisement
Quick Links
VEHICULAR SLIDE GATE OPERATOR
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
INDUSTRIAL DC
INSTALLATION MANUAL
• THIS PRODUCT MUST BE INSTALLED AND
SERVICED IN ACCORDANCE WITH THIS
MANUAL BY A TRAINED GATE SYSTEMS
TECHNICIAN ONLY.
• This operator is for use on vehicular passage
gates ONLY and not intended for use on
pedestrian passage gates.
• IHSL24UL and INSL24UL are intended
for use in Class II, III, and IV vehicular slide
gate applications.
• Visit LiftMaster.com to locate a professional
installing dealer in your area.
• This gate operator is compatible with myQ
and Security+ 2.0
accessories.
®
Access installation and technical support
guides or register this product
IHSL24ULTECH
INSL24ULTECH
®
Take a photo of the
1.
camera icon including
the points ( ).
Send it in by texting
2.
the photo to 71403.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Chamberlain IHSL24UL
Summary of Contents for Chamberlain IHSL24UL
- Page 1 • This operator is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates. • IHSL24UL and INSL24UL are intended for use in Class II, III, and IV vehicular slide gate applications. • Visit LiftMaster.com to locate a professional installing dealer in your area.
- Page 2 TABLE OF CONTENTS SAFETY Manual Disconnect ................29 Reset Button ..................29 Safety Symbol and Signal Word Review ..........2 Operator Alarm ..................30 Usage Class ...................3 Remote Control ..................30 UL325 Entrapment Protection Requirements ........3 Safety Installation Information ...............4 ACCESSORY WIRING Role of Dealers, Installers, and Trained Gate System Technicians ..4 External Control Devices ..............31 Role of End Users/Home Owners ............4 Locks ....................32...
- Page 3 Usage Class Class II - Commercial/General Access Vehicular Gate A vehicular gate operator (or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other buildings accessible by or servicing the general public. Class III - Industrial/Limited Access Vehicular Gate A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations not accessible by or...
- Page 4 SAFETY Safety Installation Information b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still 1. Vehicular gate systems provide convenience and security. Gate moving. systems are comprised of many component parts. The gate operator is c.
- Page 5 SAFETY Gate Construction Information Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org. General Requirements Vehicular Horizontal Slide Gates Gates shall be constructed in accordance with the provisions The following provisions shall apply to Class I, Class II and Class III given for the appropriate gate type listed, refer to ASTM vehicular horizontal slide gates:...
- Page 6 INTRODUCTION Carton Inventory NOT SHOWN: Documentation Packet, Chain #40 - 30 feet with master link (INSL24UL ONLY), Chain #50 - 25 feet with master link (IHSL24UL ONLY), Eye Bolt Kit, Antenna MONITORED ENTRAPMENT PROTECTION DEVICES LiftMaster Monitored Retro-Reflective Photoelectric Sensor Model LMRRUL (1)
- Page 7 INTRODUCTION Operator Specifications INSL24UL IHSL24UL Usage Classification Class II, III, and IV Main AC Supply 120 Vac, 9.3 Amps including Accessory Outlets 120 Vac, 13.0 Amps including Accessory Outlets OR 240 Vac, 1.8 Amps OR 240 Vac, 3.7 Amps Optional Transformer Kit When Optional Transformer Kit Model 3PHCONV is installed in the field, operator is rated 208/240/480/575 VAC, 5.2/4.5/2.3/1.9 A, 60 Hz, 1 PH...
- Page 8 INTRODUCTION Site Preparation Check the national and local building codes BEFORE installation. Refer also to the Site Planning Safety Checklist in the Appendix. Safety Entrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate application. Install a warning sign (two provided) on the inside and outside of the property, where easily visible.
- Page 9 INSTALLATION • To AVOID damaging gas, power or other underground utility lines, • To prevent damage to the operator or gate, DO NOT drive the limit contact underground utility locating companies BEFORE digging (nuts) actuators on the shaft past their normal positions. more than 18 inches (46 cm) deep.
- Page 10 INSTALLATION Install Without Adjustable Rails Check the national and local building codes before installation. NOTE: The rails will have to be removed for retro-fit installations. 1. Locate and anchor two posts made of 3" (7.6 cm) outer diameter heavy walled pipe. Posts should be parallel and square to the gate. 2.
- Page 11 INSTALLATION Step 2 Attach the Chain DO NOT run the operator until instructed. 1. Mount gate brackets to the vertical front and rear posts of the gate. 2. Open operator door. 3. Locate the black T-shaped manual release handle attached to the gearbox in the bottom of the cabinet. Pull firmly until it latches into place. 4.
- Page 12 INSTALLATION To prevent SERIOUS INJURY or DEATH from a moving gate: • ALL gate operator systems REQUIRE two independent entrapment • Entrapment protection devices MUST be located to protect in BOTH protection systems for each entrapment zone. the open and close gate cycles. •...
Need help?
Do you have a question about the IHSL24UL and is the answer not in the manual?
Questions and answers