Subscribe to Our Youtube Channel
Related Manuals for Digitus DN-80067
Summary of Contents for Digitus DN-80067
- Page 1 8-Port Gigabit + 2 Gigabit SFP Ethernet, Unmanaged Switch Quick Installation Guide DN-80067...
-
Page 2: Copyright Statement
Copyright Statement Our company reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of our company is prohibited. Exemption Statement This document is provided "as is". - Page 3 1.1 Package Content Before installing the Switch, make sure that the following the "packing list" listed OK. If any part is lost and damaged, please contact your local agent immediately. In addition, make sure that you have the tools install switches and cables by your hands. 1 x 8-Port Gigabit + 2 Gigabit SFP ...
-
Page 4: Hardware Specifications
1.3 Hardware Specifications IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, Standards and Protocols IEEE 802.3x, IEEE 802.3z 8 x 10/100/1000Mbps Interface Auto-Negotiation ports 2x 1000Mbps SFP ports 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) 100BASE-Tx:UTP category 5, 5e cable ... - Page 5 Power Consumption Maximum: 5.78W (220V/50Hz) Dimensions (W x D x H) 190x100x28mm Operating Temperature: 0°C~45°C Storage Temperature: -40°C~70°C Operating Humidity: Environment 10%~90% non-condensing Storage humidity: 5%~90% non-condensing 1.4 External Component Description Front Panel The front panel of the Switch consists of a series of LED indicators and 8 x 10/100/1000Mbps RJ-45 ports and two SFP ports.
- Page 6 The following chart shows the LED indicators of the Switch along with explanation of each indicator. Faceplate Indicator Status Indication Marker Power Off. Solid Status Light Power On. green Power Off. Solid Power On. green 10/100/1000 The port is BASE-adaptive Link/Act/ Solid connected at...
-
Page 7: Rear Panel
SFP ports (SFP1, SFP2): The interface card provides an interface so that you can insert a transceiver module (SFP) into the interface and connect it to the interface of another switch with cables. Each has a corresponding Link/Act LED. Rear Panel The rear panel of the Switch contains one Grounding Terminal and DC power adapter Grounding Terminal:... -
Page 8: Installing And Connecting The Switch
2. Installing and Connecting the Switch This part describes how to install your Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. 2.1 Installation Please follow the following instructions in avoid of incorrect installation causing device damage and security threat. -
Page 9: Wall Installation
2.3 Wall Installation The installation process is as follows: Step one: Please drill two suitable holes, press two expansion tubes into the two holes respectively. Step two: Insert the screw into the expansion tube. Step three: Hang the switch on the two screws. -
Page 10: Power On The Switch
2.4 Power on the Switch The Switches connected an external power adapter power 12V/1A supply, make sure you use the proper power supply. AC Electrical Outlet: It is recommended to use single-phase three-wire receptacle with neutral outlet or multifunctional computer professional receptacle. - Page 11 Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address. www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany...
Need help?
Do you have a question about the DN-80067 and is the answer not in the manual?
Questions and answers