Advertisement
Quick Links
Instructions for Installation and Care of CF Moto U-Force 1000
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done
when the temperature is 70 degrees F. or warmer. This is to allow the Velcro to stick to the roll cage better, if you must
install outside in the cold it will help to warm the Velcro inside at room temperature until ready to install.
1. Carefully open the carton and remove the rolled up Cab Enclosure on a large flat surface that is clean and free of
dirt or other material that may soil or scratch the windows of the Cab.
2. Check over the parts included in the carton with the parts list shown below:
1" Adhesive Velcro Strip
2" Adhesive Velcro Strip
"
"
"
"
"
"
"
"
"
"
Snap studs
Door Panels
If any parts are damaged or missing please contact customer service at (606) 845-7439.
3. Begin by cleaning the roll cage and plastic that surrounds the doors. Using rubbing alcohol is preferable. This step
is very important for the Velcro strips to properly adhere.
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Soft Door Rear Window Combo
CF-U-1000-DRW01
2 each
1 each
54" long
1 each
29" long
2 each
26" long
2 each
22" long
2 each
18" long
2 each
2 each
5" long
24 each ( 2 extra )
2 each
10" long
54" long
Advertisement
Related Manuals for FALCON RIDGE CF Moto U-Force 1000
Summary of Contents for FALCON RIDGE CF Moto U-Force 1000
- Page 1 2515 Bypass Rd. Flemingsburg, KY 41041 606-845-7439 Instructions for Installation and Care of CF Moto U-Force 1000 Soft Door Rear Window Combo CF-U-1000-DRW01 Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
- Page 2 SOFT DOORS: 4. Now start installation by placing the 2" adhesive Velcro strips around the outside edges of the upper door frame. Starting at the front of the frame just above the rear view mirror, place the 26" strip as shown in the photo on the next page.
- Page 3 7. Next place the 5" strip just below the bracket along the back of the roll cage 8. Last piece of Velcro will be the 10” strip that is 1” wide. This goes on the frame just behind the rear-view mirror as shown in the photo below.
-
Page 4: Rear Window
9. Lastly install the snap studs into the plastic for the bottom portion of the door. It works best to put the screw studs into the snap sockets on the door first. Then one by one pull the door in place and push the screw into the plastic making sure to put enough pressure to leave a mark. - Page 5 2. Installing the Rear Window is simple. Take the 1" wide, 54" long adhesive strip and place it across the top of the Rear Window frame. Then place the two 22" adhesive strips down the sides and then the 2” wide, 54” strip across the bottom.
- Page 6 Cab to either extreme hot or cold temperatures when storing. 3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
-
Page 7: Return Policy
Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition.