Table of Contents
Advertisement
For an explanation of these
formats, see the SYSTEM
COMMUNICATION
section in the Installation
Instructions.
*
Can only be used if the
Primary reporting format
is Ademco Contact ID.
If reporting to a Pager,
choose from 6, 7, 8, or 9,
as desired.
www.PDF-Zoo.com
45
PHONE SYSTEM SELECT
If Central Station Receiver is not on WATS line:
0 = Pulse Dial 1 = Tone Dial
If Central Station Receiver is on WATS line:
2 = Pulse Dial 3 = Tone Dial
46
REPORT FORMAT
Determine which format is to be used to report to the central station.
Enter 1 digit (0–9).
0 = 3+1; 4+1 ADEMCO Lo Speed Standard (this is the default)
1 = 3+1; 4+1 Radionics Standard
2 = 4+2 ADEMCO Lo Speed Standard
3 = 4+2 Radionics Standard
6 = 4+2 ADEMCO Express
7 = ADEMCO Contact ID Reporting
8 = 3+1; 4+1 ADEMCO Lo Speed Expanded
9 = 3+1; 4+1 Radionics Expanded
(Enter
as the 4th digit of 43 if 3+1 dialer reporting is to be used.)
Note: The maximum number of alarm and alarm restore reports
during one armed period is determined by field 92.
See field 27, which may override this field's selection.
47
SPLIT/DUAL REPORTING
Enter 0 to disable (Backup report only).
Entries 1 through 9 can be made, as indicated in the table below. Entries
6 through 9 will send a report to a pager (in addition to the selected
primary phone number), but you must enter the pager number as the
secondary phone number in field 42.
TO PRIMARY PHONE #
1 =
Alarms, Restore, Cancel
2 =
All except Open/Close, Test
3 =
Alarms, Restore, Cancel
4 =
All except Open/Close, Test
5 =
All reports
TO PRIMARY PHONE #
6 =
All reports except Open/Close
7 =
All reports
8 =
All reports
9 =
All reports except Open/Close
‡ Will report only Users 5, 6 & 8. If using 5800 series wireless button-type
devices, the zone number of the arm or disarm button (10–25) will be sent as
the user number.
Entries 6 through 9 will send a report to a pager (in addition to the selected
primary phone number), but you must enter the pager number as the secondary
phone number in field 42.
A 10-digit code is sent to the pager which will take the following format:
→
† 4-digit Subscriber No.
(as entered in field 43)
3-Digit Event Code (EEE), as follows:
911 = Alarm (NNN = Zone No.)
001 = Open, System disarmed (NNN = User No.)
002 = Close, System armed ( NNN = User No.)
811 = Trouble ( NNN = Zone No.)
†
The first digit of the Subscriber No. entered in field 43 must be 1–9 (do not use 0); the
last 3 digits can be 0–9. Failure to observe this requirement may interfere with
paging services.
– 15 –
firealarmresources.com
(1-Digit Entry)
(1-Digit Entry)
(1-Digit Entry)
TO SECONDARY PHONE #
Other Reports
Open/Close, Test
All reports
All reports
All reports
TO PAGING No.
Alarms/Open/Close, Troubles
Alarms, Troubles
Alarms/Open/Close, Troubles
Alarms, Open/Close for users #5–25 ‡
Troubles
←
3-digit User or Zone No .
SSSS–EEE –NNN
↑
Default is 0.
Default is 0.
Default is 0.
*
(Secondary)
,
(Continued)
Advertisement
Table of Contents
