Table of Contents
Advertisement
Quick Links
BLDC Shield TLE9185QX/TLE9185QX V33
User guide
Z8F80304681
About this document
Scope and purpose
This user guide describes the BLDC Shield with the TLE9185QX/TLE9185QX V33. This guide provides detailed
information on the board's content, layout, and use. The guide should be used in conjunction with the
TLE9185QX/TLE9185QX V33 datasheet, which contains full technical details on the specification and operation
of the device.
Intended audience
Hardware and software engineers that are familiar with motor control schemes and intend to evaluate the IC
TLE9185QX and TLE9185QXV33
Table of contents
About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2
Hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3
Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4
Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3
Getting started and programming the µIO stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.1
Download the graphical user interface (GUI) for the µIO stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2
Configuration wizard for the TLE9185QX/TLE9185 V33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4
Config wizard - control tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.1
SBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.2
Bridge driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
www.infineon.com
Rev.1.00
2022-06-21
Advertisement
Table of Contents
Related Manuals for Infineon TLE9185QX
Summary of Contents for Infineon TLE9185QX
-
Page 1: Table Of Contents
Configuration wizard for the TLE9185QX/TLE9185 V33 ........ -
Page 2: Introduction
The evaluation board can be used wither with a µIO stick, or with an Arduino Uno. The µIO stick is the interface between the PC and the application board such as the TLE9185QX/TLE9185QX V33. The TLE9185QX/TLE9185QX V33 SPI communication is emulated by the µIO stick, which is controlled by the PC software. -
Page 3: Hardware Description
Hardware The TLE9185QX/TLE9185QX V33 evaluation board is designed to be compatible with the µIO-stick. The µIO-stick plugs into the TLE9185QX/TLE9185QX V33 main board via a 16-pin header, and enables an easy interface to the microcontroller via USB for SPI communication. - Page 4 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 3 TLE9185QX/TLE9185QX V33 evaluation board: Overview 2 Figure 4 TLE9185QX/TLE9185QX V33 evaluation board: Overview 3 User guide Rev.1.00 2022-06-21...
- Page 5 Before sending the device into sleep mode, the wake-up source must be active. Figure 5 TLE9185QX/TLE9185QX V33 evaluation board: Jumper settings Test-mode switch: Software development mode is a dedicated SBC configuration, which is especially useful for software development. In software development mode, the watchdog is enabled by default.
- Page 6 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 6 TLE9185QX/TLE9185QX V33 evaluation board: Arduino jumper settings User guide Rev.1.00 2022-06-21...
- Page 7 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 7 TLE9185QX/TLE9185QX V33 evaluation board: Arduino connectors User guide Rev.1.00 2022-06-21...
-
Page 8: Schematics
BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Schematics Figure 8 Schematics: Connectors User guide Rev.1.00 2022-06-21... - Page 9 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 9 Schematics: BEMF detector User guide Rev.1.00 2022-06-21...
- Page 10 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 10 Schematics: Power stages User guide Rev.1.00 2022-06-21...
- Page 11 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 11 Schematics: SBC User guide Rev.1.00 2022-06-21...
-
Page 12: Layers
BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Layers Figure 12 Top layer with overlay Figure 13 Bottom layer with overlay User guide Rev.1.00 2022-06-21... - Page 13 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Figure 14 Inner layer -GND User guide Rev.1.00 2022-06-21...
-
Page 14: Bill Of Material
BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Bill of material Table 1 Bill of material Designator Quantity Description Manufacturer Manufacturer order number Through-hole .025 SQ post Samtec TSW-108-23-F-S header... SQ post-terminal strip Samtec TSW-107-23-F-S assembly A3, A4 SQ post-terminal strip... - Page 15 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Table 1 (continued) Bill of material Designator Quantity Description Manufacturer Manufacturer order number SQ Post- terminal strip Samtec TSW-105-23-F-S assembly NPN silicon AF transistor Infineon BC817K-40 Technologies OptiMOS-5 N-channel Infineon IPZ40N04S5L-2R8...
- Page 16 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 2 Hardware description Table 1 (continued) Bill of material Designator Quantity Description Manufacturer Manufacturer order number PCB terminal block Phoenix Contact 1792876 Test point THT Keystone Electronics 5001 Corp. User guide Rev.1.00 2022-06-21...
-
Page 17: Getting Started And Programming The Μio Stick
TLE9185V33 SHIELD Configuration wizard for the TLE9185QX/TLE9185 V33 Before using the µIO stick in combination with the GUI for the TLE9185QX/TLE9185QX V33, you must program the µIO stick: Set the jumper P2 to pull down the INT/TEST pin, which places the device in software development mode Set the jumper P3 to connect the LED to the VCC1 (5 V or 3.3 V regulator) - Page 18 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 3 Getting started and programming the µIO stick Figure 16 Update µIO Click , as shown in the figure below Figure 17 Dialog box: Infineon ConfigWizard Select and click (the valid version at the creation time of the document) µIO.V222.hex...
-
Page 19: Config Wizard - Control Tabs
BLDC Shield TLE9185QX/TLE9185QX V33 User guide 4 Config wizard - control tabs Config wizard - control tabs Figure 18 The two main tabs: SBC and bridge driver Figure 19 Connection status/Signaling pin status User guide Rev.1.00 2022-06-21... - Page 20 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 4 Config wizard - control tabs Figure 20 Overview of the SBC tab Figure 21 SBC: Control function, Mode User guide Rev.1.00 2022-06-21...
- Page 21 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 4 Config wizard - control tabs Figure 22 SBC: Wake-up, interrupt, timer Figure 23 SBC status User guide Rev.1.00 2022-06-21...
-
Page 22: Bridge Driver
BLDC Shield TLE9185QX/TLE9185QX V33 User guide 4 Config wizard - control tabs Figure 24 Half-bridge (HB) status Bridge driver Figure 25 Bridge driver: 1 tab - General, CSA, VDS monitoring (Mon) User guide Rev.1.00 2022-06-21... - Page 23 BLDC Shield TLE9185QX/TLE9185QX V33 User guide 4 Config wizard - control tabs Figure 26 Bridge driver: 2 tab - blank/CCP time, HBMODE, brake, TDON/TDOFF/timing Figure 27 Bridge driver: 3 tab - MOSFET drive currents User guide Rev.1.00 2022-06-21...
-
Page 24: Revision History
BLDC Shield TLE9185QX/TLE9185QX V33 User guide Revision history Revision history Document Date of Description of changes version release Rev.1.00 2022-06-27 • First release References www.hitex.com http:/www.hitex.com/uio Infineon Developer Center Launcher (formerly Infineon Toolbox) https://www.infineon.com/cms/en/ design-support/tools/utilities/infineon-developer-center-idc-launcher/ User guide Rev.1.00 2022-06-21... -
Page 25: Disclaimer
Infineon Technologies, All Rights Reserved. of any kind, including without limitation warranties of Infineon Technologies’ products may not be used in non-infringement of intellectual property rights of any any applications where a failure of the product or third party.