Canon imageCLASS D1370 Basic Operation Manual page 147

Problem You are restricted to send faxes from your computer.
You need to disable the restriction. Contact your administrator for more information.
#022
Action e -Manual → Security → Restricting to Specify Destinations and Use the Sending Functions (D1370/D1350 Only) →
Restricting to Send Faxes from Your Computer
Problem 1 The machine memory is full.
Action Print, send, or delete any documents stored in memory.
Problem 2 The data size exceeds the machine's memory capacity.
#037
Action Reduce the data resolution or change the file format to reduce the data size.
Problem 3 The memory is full when using the secure printing.
Print the documents in several batches or send the job without using the secure printing.
Action
e-Manual → Security → Entering PIN for Printing (Secure Printing) (D1370 Only) → Setting Secure Printing
Problem 1 An abbreviation of the sender's name or sender's fax number is not registered when the sender sends a fax from a computer.
Action Register an abbreviation of the sender's name as well as the sender's fax number.
#054
The destination number is more than 40 digits long when sending a fax from a computer or importing from the address
Problem 2
book.
Action Reduce the number of digits to less than 40.
Problem A job currently being processed has been canceled manually.
#099
Action Try to send or receive the document again.
Problem 1 The memory media was disconnected while it was being written to, and writing failed.
Action Check to see if the memory media was disconnected, and try writing again.
Problem 2 An error occurs when transferring images to memory media, and images cannot be transferred normally.
#408
Action Check the memory media status, and then repeat the operation.
Problem 3 The connected memory media is formatted with an unsupported file system.
Action Make sure that the memory media is formatted with a file system that is supported by the machine (FAT16 or FAT32).
Problem 1 Failed the authentication of ID or PIN in the Departmental ID Management.
Action Specify the correct dept. ID or PIN and redo the authentication.
Problem 2 The jobs with unknown IDs are restricted.
#701
Need to deactivate the restriction. Contact the system manager (administrator) for the details
Action e -Manual → Security → Specifying the Setting for Department ID Management → Specifying Whether or Not to Receive
a Print Job from an Unknown ID
Problem The image region in the memory is full. Cannot write.
Action 1 Wait until other TX jobs are completed before resending.
#703
Action 2 Delete the documents saved in the memory. If it still does not work, please turn the machine OFF and then ON again.
Action 3 Split the document into smaller subsets and send it.
Problem 1 The SMTP server name setting is incorrect.
Select the appropriate SMTP server name.
Action e -Manual → Network Settings → Setting the Machine to Be Able To Send Scanned Documents (D1370 Only) →
Configuring E-Mail Send Settings
Problem 2 The domain name setting is incorrect.
#752
Select the appropriate domain name.
Action e-Manual → Network Settings → Additional Network Settings → Setting IPv4 DNS
e-Manual → Network Settings → Additional Network Settings → Setting IPv6 DNS
Problem 3 The network is not connected.
Action Check with your network administrator to make sure that the network is operating normally.
Problem TCP/IP errors occur when sending files or e-mails. (socket and select errors, etc.)
#753
Action Make sure that the network cable connector between the machine and the computer is plugged in securely.
Problem 1 Cannot send because TCP/IP is not running properly.
Check <TCP/IP Settings>.
Action
e-Manual → Network Settings
Problem 2 The IP address is not set.
Enter the IP address.
Action
#755
e-Manual → Network Settings → Basic Network Settings → Setting the IP Address
Problem 3 When the machine was started up, IP addresses were not assigned by either DHCP, RARP or BOOTP.
After the machine is turned ON, the machine cannot communicate with the network until the time specified in <Startup
Settings> has elapsed. Wait a few seconds before resending.
Action
e -Manual → Network Settings → Additional Network Settings → Specifying a Delay Before Establishing the Network
Connection
9-9