Sharp AR-FX7 Service Manual page 61

SW39 No. 1 Received document output setting in
reception
Used to set whether all received documents are outputted at a time
after completion of reception or each document is outputted every time
when it is received.
When set to 1, all are outputted collectively after completion of reception.
When set to 0, output is made after reception of every page.
Default: 1 (Output collectively after completion of reception.)
SW39 No. 2 Specification of data output in case of a
communication error in reception
Used to set whether the image on the page where a communication
error occurred during image reception is printed or not.
"1": Setup not to print
"0": Setup to print
Default: 0 (Print)
SW39 No. 3 Memory over during reception
Used to set whether the received data are output or destroyed when
memory is over during reception.
When set to 1, the received data are outputted.
When set to 0, received data are disposed without output.
The default is 1. (The received data are outputted.)
SW39 No. 4 Output method in A3 width reception(AB
series)
Used to set whether an image of 297mm width is reduced and printed
or an image of 11" width is printed without reduction on paper of 11"
width when an image of A3 width is received. When set to 297mm
width, if a document of 11" is received, both ends are not printed.
When set to 1, printing is made on paper of 297mm width.
When set to 0, printing is made on paper of 11" width.
Default: 1 (Printing is made on paper of 297mm width.)
SW39 No. 5 Output method in A4 width reception (AB series)
Used to set whether printing is made on paper of 8.5" width or of
210mm width when an image of A4 width is received. When set to 8.5"
width, if printed on A4(R), the image is reduced. When set to 210mm
width, if a document of 8.5" is received both ends are not printed.
When set to 1, printing is made on paper of 8.5" width.
When set to 0, printing is made on paper of 210mm width.
Default: 0 (Printing is made on paper of 210mm width.)
SW39 No. 6 Output method in A3 width reception (Inch
series)
Used to set whether an image of 297mm width is reduced and printed
or an image of 11" width is printed without reduction on paper of 11"
width when an image of A3 width is received.
When set to 1, printing is made on paper of 297mm width.
When set to 0, printing is made on paper of 11" width.
Default: 0 (Printed on paper of 11" width)
SW39 No. 7 Output method in A4 width reception (Inch
series)
Used to set whether printing is made on paper of 8.5" width or of
210mm width when an image of A4 width is received.
When set to 1, printing is made on paper of 8.5" width.
When set to 0, printing is made on paper of 210mm width.
Default: 1 (Printed on paper of 8.5" width)
SW39 No. 8 Relay data output
Used to set whether the received document is outputted from the relay
direction station when relay broadcasting direction is received.
When set to 1, the document received from the relay instruction station
is printed.
When set to 0, the document received from the relay instruction station
is not printed.
Default: 1 (Print)
SW40 No. 1 Rotation print
Used to set Enable/Disable of rotation print when the received docu-
ment can be printed by rotation.
When set to 1, the received document is printed by rotation.
When set to 0, the received document is not rotated.
Default: 1 (Printed by rotation)
SW40 No. 2 Override print setup
Used to set whether the latter print job is performed or not when the
former print job is suspended at the first page due to printable paper
empty.
When set to 1, override print is allowed.
When set to 0, override print is not allowed.
Default: 1 (Override print is allowed)
SW40 No. 3 Page number print setup
Used to set whether the page number is added to the position where
date and the sender's information are printed. (In memory transmis-
sion, page number/total number of pages)
When set to 1, the page number is printed.
When set to 0, the page number is not printed.
Default: 1 (The page number is printed.)
SW40 No. 4 Index print setup
Used to set whether the index is printed on the received document or not.
When set to 1, the index is printed on the received document.
When set to 0, the index is not printed.
Default: 0 (The index is not printed.)
SW40 No. 5 Duplex rotation print
Used to set the duplex rotation print.
Default: 1 (YES)
SW40 No. 6 Reception data duplex print
Used to set YES/NO of the reception data duplex print.
Default: 0 (NO)
SW40 No. 7 Specification of print sequence in duplex print
Used to specify the print sequence in duplex print.
Default: 1 (Print order (214365...))
SW40 No. 8 Specification of rotating direction duplex
back surface print
Used to specify the rotating direction duplex back surface print.
Default: 1 (180° rotation)
SW41 No. 1 External telephone connection
If this switch is not set to YES, an external telephone cannot be used.
Default: 1 (YES)
SW41 No.2–No.4 Inhibited to use.
SW41 No.5–No.8 Interval from completion of a
transmission to the next call-out
Used to set the time interval between the end of a communication and
a call for the next communication.
Setup is made by binary input in the interval of 0 – 15sec.
Default: 6sec
SW42 No.1–No.3 Communication end buzzer sound
length
Used to specify the length of the communication end sound.
Default: 3.0 sec.
SW42 No.4, No.5 Transmission end sound tone
Used to set the transmission end beep sound tone in transmission.
Default: 0 1 (1000Hz)
SW42 No.6, No.7 Reception end sound tone
Used to set the reception end sound beep tone in reception.
Default: 0 1 (1000Hz)
AR-FX7 SOFT SWITCH 7 - 34