Page 2
Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well-ventilated area and wear...
Pistol Grip (Handheld) Remote Special Considerations ................7 Power Up the Pistol Grip (Handheld) Remote ....................7 Associate Mode .............................7 MIN / MAX Adjustment Fundamentals ......................8 MIN / MAX Adjustment Procedure for 70735257 & 70735258 ............... 8 Battery Installation Battery Installation / Replacement .......................12 70735258 SII Base Receiver 70735258 - SII Receiver Radio Remote (Base Unit) - Electric Crane ............
Introduction Section - 1 Equipment Safety PERSONNEL REQUIREMENTS Certain inherent risks are associated with heavy equipment. Personnel working in the area of these vehicles are subject to certain hazards that cannot be guarded against by mechanical means, but only by the exercise of intelligence, care, and common sense.
List of Equipment Section - 2 Section - 2 List of Equipment 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
Page 8
List of Equipment Section - 2 70735257 & 70735258 PART NO. DESCRIPTION QTY. 70735257 TRANSM-RAD REM S2 ELECTRIC 70735258 RECEIVER-RAD REM S2 ELECTRIC assoc assoc X ON An Oshkosh Corportation Company store TX OFF 70735257 TO LOAD 70735260 BU-2H20XF-11003 707352658...
70735257 SII Handheld Remote Section - 3 70735257 - SII Radio Remote (Handheld) Transmitter - Electric Crane assoc assoc TX ON LEDs LED 1 GREEN store LED 2 AMBER LED 3 LED 4 BATT AMBER assoc ASSOC X ON ACTION...
LEDs TX and RX rapidly blinking. Associate Mode The pistol grip (handheld) remote (70735257) allows 1-to-1 association to a receiver base unit (70735258). To associate there must be a clear line of sight between the handheld and the base, and both units must be OFF (powered down).
• Releasing the function switch used to enter trigger adjustment. MIN / MAX Adjustment Procedure for 70735257 & 70735258 1. Turn the controller on by twisting the red STOP button clockwise until the button releases (pops UP). 2. Move Switch S1 UP and allow it to return to center.
Page 13
70735257 SII Handheld Remote Section - 3 4. Release switches S7 and S1 5. Operate any of the function toggles either UP or DOWN and hold it in position. Continue to hold the function switch throughout the entire Adjustment procedure. The Base Unit LED (ERR) lights solid indicating MIN Adjust Mode.
Page 14
This page left intentionally blank 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
Battery Installation Section - 4 Battery Installation / Replacement 1. The handheld remote unit is powered by four-size AA alkaline batteries. When installing batteries, be sure to observe proper polarity as marked on the inside of the compartment to avoid damaging the unit. To replace or install batteries in the handheld: 2.
70735258 SII Base Receiver Section - 5 70735258 - SII Receiver Radio Remote (Base Unit) - Electric Crane BASE UNIT LEDs +V1, +V2, +V3 BASE UNIT VOLTAGE OK HEALTH RF TX 7.4mm (.29") DIA RF RX CAN TX CAN RX OUPUT ACTIVE INPUT ACTIVE ERROR...
70735258 SII Base Receiver Section - 5 70735258 - Base Unit Configuration CHANNEL TYPE* FUNCTION ACTIVATED BY: SETTINGS WIRE NOT USED NOT USED -VDC S2+/- ,or S4+/- TOGGLE SWITCH PROPORTIONAL OPERATED TRIGGER OUPUT BEFORE TRIGGER or 5+/- DEPRESSED NOT USED +VDC RED/WHT LO-HS-M...
70735258 SII Base Receiver Section - 5 70735258 - Base Unit Hardware Specs / Base Unit Safety Link / Base Unit Hardware BASE UNIT HARDWARE SPECIFICATIONS REQUIRED FIELDS DESCRIPTION DETAILS CONTROL POWER 7-28VDC USING 12VDC RF FREQUENCY 2400MHz 2405-2480MHz @ 100 mW ANTENNA OPTION INTERNAL DISCRETE CHANNELS...
Page 21
70735258 SII Base Receiver Section - 5 BASE UNIT HARDWARE (70735258) ITEM DESCRIPTION POWER VIN: + 7 TO +28 VDC -20°C TO 55° C OPERATING TEMP: (-4°F TO 131° F) -40° C TO 85° C STORAGE TEMP: (-40° F TO 185° F) ENVIRONMENT HUMIDITY: 0 TO 100% IEC60068-2-8...
Page 22
This page left intentionally blank 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
DRAW IS A NORMAL CONDITION.) HEALTH LED BLINKING RAPIDLY INDICATES AN INTERNAL PROBLEM. • CONTACT IMT TECHNICAL SUPPORT IF THE RECOMMENDED SOLUTIONS DO NOT RESOLVE THE ISSUE, CONTACT IMT TECHNICAL SUPPORT DEPARTMENT. 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
Identification/ Locations / Exposure Section - 7 Exposure to Radio Frequency Energy The handheld remote control and base units contain radio transceivers. When active, handheld remotes and base units send out radio frequency (RF) energy through either internal (remote/base unit) or external (base unit only) antennae.
Identification/ Locations / Exposure Section - 7 Identification Label Locations Model: BU-2H20XF-11002 Contains: FCC ID: LOBSRF305 IC: 7955A-SRF305 Input: 9-365 3A per channel 8A Max Total NOTE: THE BASE UNIT AGENCY LABEL POSITION IS IDENTICAL FOR ALL INTERNAL ANTENNA AND EXTERNAL ANTENNA BASE UNITS 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
Page 28
This page left intentionally blank 06/15/2022 SII Telescopic Proportional Electric Crane Radio Remote...
Page 29
IMT is an Oshkosh Corporation company Oshkosh is a registered trademark and the Oshkosh logo is a trademark of Oshkosh. IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.