Related Manuals for Sinclair S-THERM GSH-TRB2+ Series
Summary of Contents for Sinclair S-THERM GSH-TRB2+ Series
- Page 1 USER’S MANUAL SPLIT INVERTER ALL-IN-ONE AIR TO WATER HEAT PUMP GSH-XXXTRB2 + GSH-XXXERB GSH-XXXTRB2 + GSH-XXXERB2 GSH-XXXTRB2-3 + GSH-XXXERB-3...
- Page 3 To Users Thank you for selecting Sinclair’s product. Please read this instruction manual carefully before installing and using the product, so as to master and correctly use the product. In order to guide you to correctly install and use our product and achieve expected operating effect, we hereby instruct as below: (1) This instruction manual is a universal manual, some functions are only applicable to particular product.
-
Page 4: Table Of Contents
Contents Safety Notices (Please be sure to abide) ..............1 General ........................2 1.1 Home Page ........................2 1.2 Menu Page ........................3 1.3 Backlight ...........................4 2. Operation Instructions ....................4 2.1 ON/OFF ..........................4 2.2 Function Setting ........................5 2.4 Commissioning Parameter Setting .................16 2.5 Viewing ...........................26 2.6 General Setting .......................30 3. -
Page 5: Safety Notices (Please Be Sure To Abide)
Safety Notices (Please be sure to abide) Do not install the control where it is damp or exposed to direct sunlight. Once the air conditioning unit is installed where possibly subject to electromagnetic interference, shielded twisted pairs should be used as signal lines and other communication lines. Be sure communication lines are wired to the correct ports, or normal communication would fail. -
Page 6: General
General (This picture is just for reference) This display panel uses the capacitor touch screen for input operation. The valid touching area indicates the black rectangle when the display panel lights off. This control panel is of high sensitivity and will response to unexpected click by the foreign matters on the display panel. -
Page 7: Menu Page
●Under the combined modes, the temperature set point is for space heating or cooling. Only under the water heating mode, it is for water heating. ●It will go back automatically to the homepage when there is no any operation in ten minutes. 1.2 Menu Page Menu Page Above the menu, the corresponding icon will be displayed based on the mode and status of the controller. -
Page 8: Backlight
Hot water + Cooling Back Quiet Menu page Sanitation Save Emergency Error [Notes] ●The “Cooling” mode is unavailable to the heating only unit. ●The “Hot water” mode is unavailable to the heating only unit. ●The “Heating + Hot water” (“Hot water” takes the priority) is unavailable to the mini chiller. ●The “Hot water + Heating”... -
Page 9: Function Setting
ON Page 2.2 Function Setting [Operation Instructions] 1.At the menu page, by touching “FUNCTION”, it will go to the function setting page as shown in the figure below. FUNCTION Setting Page 2.At the function setting page, by touching the page turning key, it will access to the last or next page. When setting is finished, by touching the menu page icon, it will directly back to the menu page;... - Page 10 Item Range Default Remarks 1. When the water tank is unavailable, it will be Fast hot water On/Off reserved. 1. When the water tank is available, it will be defaulted to be “Hot water”; when unavailable, it will Cool + hot water Cool/Hot water Hot water be reserved.
- Page 11 ●When the water tank is unavailable, only “Heat” and “Cool” mode are allowed. ●When the water tank is available, “Cool”, “Heat”, “Hot water”, “Cool+ Hot water”, and “Heat+ Hot water” are allowed. ●For the heat pump, the “Cool” mode is allowed; for the heating only unit, “Cool+ Hot water” and “Cool” are unallowable.
- Page 12 Timer for Quite Mode This setting will be saved by touching the corner at the upper right corner. [Notes] ●It can be set under both ON and OFF statuses, but will work only when the main unit is turned on. ●When it is set to “On”, it will automatically back to “Off”...
- Page 13 2.2.7 Weekly Timer [Operation Instructions] 1.At the function setting page, by touching “Weekly timer”, it will go to the setting page as shown below. 2.At the “Weekly timer” setting page, as shown in the figure below, the weekly timer can be set to “On” or “Off”. 3.At the “Weekly timer”...
- Page 14 3.Then, this setting will be saved by touching the “Save” icon. [Notes] ●This function is unavailable to mini chillers. ●This setting can be activated only when “Water tank” is set to “With”. When “Water tank” is set to “Without”, this function will be deactivated. ●This setting can be done no matter if the unit is turned on or off.
- Page 15 [Notes] ●When “Clock timer” has been set and “Hot water” mode is involved, in this case, if “Water tank” is changed to “Without”, “Hot water” will be automatically switched to “Heat”, and “Cool/Heat + Hot water” will be switched to “Cool/Heat”.
- Page 16 [Notes] ●When “Weekly timer”, “Preset mode”,“Clock timer” “Temp. timer” have been set at the same time, then the latter takes the priority. ●This setting is valid only when the unit is turned on. ●Under the “Cool” or “Cool+Hot water” mode, the setting targets at “WT-Cool”; while under the “Heat” or “Heat+Hot water”...
- Page 17 ●Upon power failure, “Emergen. mode” will back to “Off”. 2.2.13 Holiday Mode [Operation Instructions] At the function setting page, select “Holiday mode” and set it to “On” or “Off”. [Notes] ●This function can be activated only when the unit has been turned off, otherwise a prompt dialog box will pop up, saying “Please turn off the system frist!”.
- Page 18 ●When the water tank is available, the preset mode can be “Heat”, “Cool”, or “Hot water”; however, when the water tank is unavailable, the preset mode can only be “Heat” or “Cool”. ●“Start timer” should be earlier than “End timer”, otherwise a dialog will pop up, saying “time setting wrong”. ●The setting for “Preset mode”...
- Page 19 Parameter Setting Page 2.At the menu setting page, by touching the page turning keys, it is able to switch to the page where the desired parameter is. 3.After that, this setting will be saved by touching “OK” and then the unit will run based on this setting. While this setting will give up by touching “Cancel”.
-
Page 20: Commissioning Parameter Setting
2.4 Commissioning Parameter Setting [Operation Instructions] 1.At the menu page, by touching “Commission” and then entering the correct password (000048) in the pop-up window, the commissioning parameter page will be accessed, where the left side is for the function setting and the right side is for the parameter setting, as shown in the figure below. - Page 21 Item Range Default Description Air removal On/Off Floor debug On/Off Manual On/Off defrost “ ” Force mode Off/Force-cool/Force-heat Force-cool is unavailable to heating only units. 1. This setting is allowed when the water tank is Tank heater Logic 1/Logic 2 Logic 1 available and the unit is OFF.
- Page 22 2.4.2 2-Way valve [Operation Instructions] At the commissioning parameter setting page, by touching “Cool 2-Way valve” or “Heat 2-Way valve”, the control panel will access to the corresponding setting page. [Notes] ●This setting is unavailable to heating only units. ●Under “Cool”, or “Cool + Hot water” mode, “Cool 2-Way valve” will decide the status of the 2-way valve; while under “Heat”...
- Page 23 [Notes] ●When “Water tank” is set to “Without”, the “Air + hot water” mode is unavailable. ●When “Floor debug” and “Emergen.mode” have activated, function of the thermostat will be invalid. Temp.timer will be deactivated automatically ●When “Thermostat” is set to “Air” or “Air + hot water”, “ ”...
- Page 24 2.The water pump for other thermal must be always active under the “Heat” mode. 3.Under the “Heat” mode, the 2-way valve will be controlled based on the setting of the control panel. During heating operation, the water pump of the heat pump unit will be stopped; however, during standby status, the water pump will start but the other thermal will stop.
- Page 25 Other Thermal Control Product Mode Remark Required accessories Heat Available RT5 temperature sensor Hot water Available Extra 3-way valve, water tank sensor Monobloc Heat+Hot Extra 3-way vlave,RT5 temperature sensor, Available water Water tank sensor Heat Available RT5 temperature sensor Hot water Available Extra 3-way valve, water tank sensor Split...
- Page 26 2.4.8 Remote Sensor [Operation Instructions] At the commissioning parameter setting page, by touching “Remote sensor”, the control panel will access to the corresponding setting page, where it can be set to “With” or “Without”. [Notes] ●This setting will be memorized upon power failure. ●Only when “Remote sensor”...
- Page 27 3.When this setting is finished, by pressing “Start” this setting will be saved and start working, and by pressing “Stop” the function will halt. [Notes] ●This function can be activated only when the unit is turned off. When it is done with the unit keeping “On”, a window will pop up, saying “Please turn off the system first!”.
- Page 28 [Notes] ●When “Gate-Ctrl.” has been activated; the display panel will detect the card state. When the card has inserted, the unit will run normally. When the card is drawn out, the controller will turn off the unit at once and back to the homepage.
- Page 29 2.4.17 Control Logic of the Water Tank Heater [Operation Instructions] At the commissioning parameter setting page, by touching “Tank heater”, it will access to the setting page of control logic for the water tank heater. [Notes] ●“Reserved” will be displayed when the water tank is unavailable. ●This setting can be done only when the unit is off.
-
Page 30: Viewing
Display Full Name Range Default Remark Name T-HP max T-HP max 40~55℃ 104~131°F 50℃ /122°F It is unavailable to mini chillers. [Notes] ●For parameters with different defaults at different conditions, once the current condition changes, the corresponding default also will change. ●All parameters at this page will be memorized upon power failure. - Page 31 Full Name Displayed Name Status Remarks Status of the heater 1 for the main unit HP-heater 1 On/Off Status of the heater 2 for the main unit HP-heater 2 On/Off Status of the Chassis heater Chassis heater On/Off Status of the heat exchanger heater Plate heater On/Off Status for the system defrosting...
- Page 32 Full Name Displayed Name Remarks Economizer inlet temperature T-economizer in Economizer outlet temperature T-economizer out Remote room temperature T-remote room “NA” for mini chillers Discharge pressure Dis. pressure Weather-dependent target temperature T-weather depend 2.5.3 Error Viewing [Operation Instructions] At the “VIEW” page, by touching “Error”, it is able to view errors of the unit, as shown in the figure below. Error View Page [Notes] ●The control panel can display real-time errors.
- Page 33 Full Name Displayed Name Water tank temperature sensor error Tank sens. ("NA" for mini chillers) Remote room temperature sensor error T-Remote Air Protection for the flow switch of the heat pump HP-Water Switch Welding protection to the auxiliary electric heater 1 of the heat pump Auxi.
-
Page 34: General Setting
[Notes]: ●The error log can accommodate up to 20 pieces of error. Name and occurrence time are available for each error. ●When error log exceeds 20, the latest will supersede the earliest. 2.5.5 Version Viewing [Operation Instructions] At the “VIEW” page, by touching “Version”, the control panel will go to the version view page, where it is able to view both the program version and protocol version. - Page 35 Item Range Default Remarks Italiano/English/Español/ Nederlands/Français/ Deutsch/Български/Polski/ Language English Suomi/Svenska/Türkçe/ Magyar/Lietuvių/Hrvatski/ Čeština/Srpski/… WiFi On/Off 2.6.1 Clock Setting [Operation Instructions] 1.At the “GENERAL” setting page, by touching “Time&Data”, it will go to the setting page as shown in the figure below. Time&Data Page 2.The mouse roller can change the date and time value.
-
Page 36: Intelligent Control
3. Intelligent Control As shown in the figure below, remote control via a smart phone is available for the control panel. [Notes]: ●Make sure the smart phone or tablet computer adopts standard Android or Ios operation system. For detailed version, please refer to the APP. ●The Wi-Fi function doesn’t support Chinese Wi-Fi network name. - Page 37 “Sign up ” for registration. 2.Open EWPE SMART APP and click 3.Except sign in in the prompt interface, you can also enter the homepage and click the profile picture at the left upper corner to sign in.
- Page 38 4.Click "+" at the right upper corner of homepage to add device. After selecting “ATW HP” , the APP interface will provide relevant operation instructions.
- Page 39 Reset the air conditioner (refer to the operation instructions in APP interface) and click “Next” to add home appliance automatically (Wi-Fi password shall be input). Or after setting and energizing the air conditioner, click “Add appliance manually” at the right upper corner to select the wireless network for controlling the device. Then confirm family Wi-Fi and arrange configuration.
-
Page 40: Setting Of Main Functions
After accomplishing device reset and filling correct information, search device and arrange configuration. 3.2 Setting of Main Functions 1.Set mode and temperature. -
Page 41: Setting Of Other Functions
2.Click Func at the left lower corner in device operation interface to enter advanced settings. 3.3 Setting of Other Functions Click the profile picture at the left upper corner of homepage and set each function in the following menu. - Page 42 3.3.1 Home management Click “Home management” to create or manage family. You can also add family members according to the registered account. 3.3.2 Help Click “Help” and view the operation instructions of the APP.
- Page 43 3.3.3 Feedback Click “Feedback” to submit feedback.
- Page 44 SINCLAIR CORPORATION Ltd. 1-4 Argyll St. London W1F 7LD Great Britain www.sinclair-world.com This product was manufactured in China (Made in China). REPRESENTATIVE SINCLAIR Global Group s.r.o. Purkynova 45 612 00 Brno Czech Republic TECHNICAL SUPPORT SINCLAIR Global Group s.r.o. Purkynova 45...