Subscribe to Our Youtube Channel
Related Manuals for LINK-MI LM-CX100IR
Summary of Contents for LINK-MI LM-CX100IR
- Page 1 Operation Manual LINK-MI LM-CX100IR HDMI Extender over single 100m/328ft Coaxial Cables with IR Control OperationManual ----------1----------...
- Page 2 Operation Manual Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Introduction The HDMI Over Single Coax Extender sends HDMI signals Over just one 75Ohm Coaxial cable -- up to100m away.
- Page 3 Operation Manual receiver. The transmitting unit is used to capture the HDMI input with IR signals and carries the signals via one coaxial cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR and serial control signals. The Extender offers the most convenient solution for HDMI extension over a single coaxial cable with long distance capability, and is the perfect solution for any application.
- Page 4 Operation Manual Audio and video are transmitted digitally over the 75Ohm RG-6U Coax cable with zero signal loss. Single Link Range: 1080p/60, 12 bit color depth. Compliant with HDMI 1.3, HDCP 1.1 standards. Supports digital video formats in Deep Color Mode at up to 12bits/color.
- Page 5 Operation Manual Package Contents: (1) [TX & RX] (2) IR Blaster (TX) (2) IR Receiver (RX) (2) DC 5V in line power supply (1)User Manual Specification Frequency Bandwidth 225MHz/link (HDMI 1.3) In/Output Support Resolution 480i, 576i, 720p@50/59.94,60 1080i@50/59.94/60 1080p@23.98/24/25/29.97/30/50 /59.94/60 ----------5----------...
- Page 6 Operation Manual Input TMDS Signal: 3.3 volts Input DDC Signal: 5.0 volts/P-P Protection Human body ±8kV (air-gap discharge) model ±4kV (contact discharge) Coaxial Cable Distance Full HD up to 100M (RG-6U cables) HD up to 200M (RG-6U cables) SD up to 300M (RG-6U cables ) Dimension (mm) 100(D)x105(W)x25(H) Weight (g)
- Page 7 Operation Manual Operation temperature: 32~104 °F Storage temperature: -4 ~140 °F Relative humidity: 20~90 % RH (no condensation) Operation Controls and Functions Transmitter Front Panel Rear Panel LINK LED:This LED will illuminate when the device is connected with HDMI source ----------7----------...
- Page 8 Operation Manual HDMI IN: This slot is to connect with the input source equipment such as DVD or Blue-ray player with connection cable for input video and audio signal transmission. IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR receiver.
- Page 9 Operation Manual Position EDID Description 1080p, 2CH PCM 48KHz 1080p, 5.1CH PCM 48KHz 1080p, 7.1CH PCM 48KHz 1080i, 2CH PCM 48KHz Power LED: This red LED will switch on when the device is connected with the power supply. DC 5V: Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet.
- Page 10 Operation Manual Receiver Front Panel Rear Panel LOCK LED: This LED will illuminate when the HDMI signal from the transmitter is stable. HDMI Out: This slot is where you connect a HDMI display with a HDMI cable . IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR receiver.
- Page 11 Operation Manual IR TX: Connect the IR Blaster cable included in the package for IR signal transmission. Pace the IR blaster in direct line-of-sight of the equipment to be controlled. Power LED: This red LED will switch on when the device is connected with the power supply.
- Page 12 Operation Manual Wideband IR(20KHz---60KHz) Introduction ----------12----------...
- Page 13 Operation Manual IR RECEIVER (RX) To control the source: Plug IR Receiver into IR RX port of receiver unit; place receiver at or near display. To control the display: Plug IR Receiver into IR RX port of transmitter unit; place receiver in position where it is able to receive remote signals. IR BLASTER (TX) To control the source: Plug IR Blaster into IR TX port of transmitter unit;...
- Page 14 Operation Manual ----------14----------...
- Page 15 Operation Manual Connection and Installation Connect the HDMI Transmitter output BNC ports using single RG6 coaxial cables to included Receiver. It is strongly recommended that factory terminated cable assemblies be used and their length shall not exceed 328 ft respectively. Connect the HDMI output from the Receiver to high-definition display devices such as HD-LCD, HD-DLP and HD projectors with HDMI input interfaces.
- Page 16 Operation Manual ----------16----------...
Need help?
Do you have a question about the LM-CX100IR and is the answer not in the manual?
Questions and answers