Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HGLRC Racewhoop30
Summary of Contents for HGLRC Racewhoop30
- Page 1 Racewhoop30 FPV Racing Drone Manual www.hglrc.com...
-
Page 2: Table Of Contents
Voltage and current parameters setting.....................8 Setting up the receiver..........................9 VTX serial port use. DJI serial port use....................10 GPS parameters setting...........................11 Check receiver signal..........................12 Select flight mode startup mode......................13 OSD settings..............................14 LED settings..............................15 Troubleshooting............................16 ..................Package IncIuded FPV Racing Drone*1 Accessory Package*1 Racewhoop30 www.hglrc.com... -
Page 3: Product Specifications
1.Product Specifications Product parameters Racewhoop30 VTX FPV Racing Model Drone Frame Kit Racewhoop30 Frame Kit Flight Controller Zeus F722 mini Flight Controller 28A 4in1 ESC Zeus VTX 350mW 2105.5 Motor Motor 4S KV3600 6S KV2800 Support Neceiver SBUS .DSMX.CRSF Input Voltage 3-6S Lipo www.hglrc.com... -
Page 4: Interface Description
2.Interface Description www.hglrc.com... -
Page 5: Check The Flight Control Drive
3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator enter DFU mode ， www.hglrc.com... - Page 6 5.Click Select firmware version Load firmware Waiting for 6.Click completion It will be prompted upon completion 7. open betaflight configurator computer. Betaflight Automatically assigned port click “Connect” Enter Controller plugged into the setup interface（Different computer COM） ， www.hglrc.com...
-
Page 7: Calibration Accelerometer
4. Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again 5.UART serial port use 1.UART1 uses the receiver 2.UART2 uses GPS 3.UART3 uses 5.8G VTX 4.UART4 uses DJI 5.UART6 uses ESC telemetry www.hglrc.com... -
Page 8: Select Aircraft Model
6.Select aircraft model Select model Click I understand the risks Click Click Push Master to check motor “ ” steering Master Steering can be changed at BLHeliSuite “ ” www.hglrc.com... -
Page 9: Choose Esc Protocol
7.Choose ESC protocol 1.Choose the right ESC protocol, the optional universal protocol DSHOT600. 8.Voltage and current parameters setting 1.Click Setting parameters www.hglrc.com... -
Page 10: Setting Up The Receiver
9.Setting up the receiver 1.Receiver connection diagram www.hglrc.com... - Page 11 2.Click have found UART1 Open the receiver serial port “ ” 3.Set the SBUS receiver 4.Set the DSMX receiver 5.Set the CRSF receiver www.hglrc.com...
- Page 12 10.VTX serial port use wiring . DJI serial port use wiring 1. 5.8G VTX connection www.hglrc.com...
- Page 13 2. DJI FPV Air Unit wiring 3. 5.8G VTX serial port opens. The protocol is selected according to its own VTX protocol. 4. DJI serial port opens www.hglrc.com...
- Page 14 In the “Scr Layout” sub-menu, you can move the OSD elements (like battery voltage, mAh, and so forth) around on the screen. The “Alarms” sub-menu lets you control when the OSD will try to alert you that battery voltage is too low or mAh consumed is too high. www.hglrc.com...
-
Page 15: Gps Parameters Setting
The screen to the right shows the current vTX settings. From here, you can change the frequency band, channel, and power level of the video transmitter. After making the changes, move the cursor to “Set” and press roll-right to confirm the settings. 11.GPS parameters setting 1.GPS connection diagram www.hglrc.com... -
Page 16: Check Receiver Signal
2.Open the GPS serial port 3.When using the GPS function, remember to configure the serial port (via the Ports tab). 12.Check receiver signal Check the remote control output signal 1.Click www.hglrc.com... -
Page 17: Select Flight Mode Startup Mode
1.Click channel (below are for reference only) 14.OSD settings the OSD Settings, according to the need to choose, drag Click the OSD schematic diagram of the parameters can be adjusted. www.hglrc.com... -
Page 18: Led Settings
● Keep focus on the polarity. Check carefully before power supply. ● Cut off the power when you connect, plug and pull anything. ● The refresh rate of PID and Gyroscope is up to 8K/8K. www.hglrc.com... - Page 19 "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct www.hglrc.com...