Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HGLRC Sector4 FR Freestyle FPV Drone HD
Summary of Contents for HGLRC Sector4 FR Freestyle FPV Drone HD
- Page 1 Sector4 FR Freestyle FPV Drone HD Manual www.hglrc.com...
-
Page 2: Table Of Contents
Voltage parameters setting........................9 Setting up the receiver..........................10 VTX serial port use. DJI serial port use....................11 Check receiver signal..........................12 Select flight mode startup mode......................13 OSD settings..............................14 LED settings..............................15 Troubleshooting............................16 Package IncIuded Sector4 FR Freestyle FPV Drone HD *1 Accessory Bag*1 www.hglrc.com... -
Page 3: Product Specifications
1.Product Specifications Product parameters Model Sector4 FR Freestyle FPV Drone HD Frame Kit Sector4 FR FPV Freestyle Frame Kit Flight Controller Zeus 25 AIO CADDX Vista Nebula Nano 1804Motor Motor 4S KV3500 Support receiver SBUS .DSMX.i.BUS Input Voltage 3-4S Lipo Weight 160.5g... -
Page 4: Interface Description
2.Interface Description 3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver www.hglrc.com... - Page 5 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator enter DFU mode ， 5. Click Select firmware version www.hglrc.com...
- Page 6 Load firmware Waiting for completion 6.Click It will be prompted upon completion 7.open betaflight configurator 。Controller plugged into the computer. Betaflight Automatically assigned port，click “Connect” Enter setup interface（Different computer COM） www.hglrc.com...
-
Page 7: Calibration Accelerometer
4.Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again 5.UART serial port use 1.UART1 uses the receiver 2.UART2 uses GPS 3.UART3 uses VTX/DJI 4.UART4 uses WiFi module 5.UART6 uses ESC telemetry www.hglrc.com... -
Page 8: Select Aircraft Model
6.Select aircraft model Select model Click I understand the risks 2.Click Click Push Master to check motor “ ” steering Master Steering can be changed at BLHeliSuite “ ” www.hglrc.com... -
Page 9: Choose Esc Protocol
7.Choose ESC protocol 1.Choose the right ESC protocol, the optional universal protocol DSHOT600. 8. Voltage and current parameters setting 1.Click Setting parameters www.hglrc.com... -
Page 10: Setting Up The Receiver
9.Setting up the receiver 1.Receiver connection diagram 2.Click have found UART1 Open the receiver serial port “ ” www.hglrc.com... - Page 11 3.Set the SBUS receiver 4.Set the i.BUS receiver 5.Set the DSMX receiver .Set the CRSF receiver www.hglrc.com...
- Page 12 10.VTX serial port use wiring . DJI serial port use wiring 1. VTX connection 2. DJI FPV Air Unit wiring www.hglrc.com...
-
Page 13: Check Receiver Signal
3. DJI serial port opens 11.Check receiver signal Check the remote control output signal 1.Click www.hglrc.com... -
Page 14: Select Flight Mode Startup Mode
1.Click channel (below are for reference only) 13.OSD settings the OSD Settings, according to the need to choose, drag 1.Click the OSD schematic diagram of the parameters can be adjusted. www.hglrc.com... -
Page 15: Led Settings
● Keep focus on the polarity. Check carefully before power supply. ● Cut off the power when you connect, plug and pull anything. ● The refresh rate of PID and Gyroscope is up to 4K/4K. www.hglrc.com... - Page 16 "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct www.hglrc.com...
Need help?
Do you have a question about the Sector4 FR Freestyle FPV Drone HD and is the answer not in the manual?
Questions and answers