Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HGLRC Veyron35 CR Pusher
Summary of Contents for HGLRC Veyron35 CR Pusher
- Page 1 Zeus35 Pro AIO Flight Controller Manual www.hglrc.com...
-
Page 2: Table Of Contents
Voltage and current parameters setting.....................8 Setting up the receiver..........................9 VTX serial port use. VTX uses OSD smart audio................10 GPS parameters setting...........................11 Check receiver signal..........................12 Select flight mode startup mode......................13 OSD settings..............................14 LED settings..............................15 Troubleshooting............................16 ..................Package IncIuded Zeus35 Pro AIO*1 Accessory Bag*1 www.hglrc.com... -
Page 3: Product Specifications
Zeus35 Pro AIO Weight 13.8g Input Voltage 3-6S Usage for 100mm-450mm Frame Kit Installing Hole 20x20mm/M3 Dimensioms 40.0x34.0mm FC Firmware BF ZEUSF722_AIO(HGLR) STM32F722 MPU6000 9V/1A 5/2A BlackBox UARTS ESC Firmware BL_S Current Sensor not support Constant Current Peak Current 40A（5s） www.hglrc.com... -
Page 4: Interface Description
2.Interface Description 3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver www.hglrc.com... - Page 5 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator enter DFU mode ， 5.Click Select firmware version www.hglrc.com...
- Page 6 Load firmware Waiting for 6.Click completion It will be prompted upon completion 7.open betaflight configurator computer. Betaflight Automatically assigned port click “Connect” Enter Controller plugged into the setup interface Different computer ， （ ） www.hglrc.com...
-
Page 7: Calibration Accelerometer
4.Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again 5.UART serial port use 1.UART1 uses the receiver 2.UART2 uses VTX/DJI 3.UART3 4.UART4 uses GPS 5.UART6 www.hglrc.com... -
Page 8: Select Aircraft Model
6.Select aircraft model Select model Click I understand the risks Click Click Push Master to check motor “ ” steering Master Steering can be changed at BLHeliSuite32 “ ” www.hglrc.com... -
Page 9: Choose Esc Protocol
7.Choose ESC protocol 1.Choose the right ESC protocol, the optional universal protocol DSHOT600. 8.Voltage and current parameters setting 1.Click Setting parameters www.hglrc.com... -
Page 10: Setting Up The Receiver
9.Setting up the receiver 1.Receiver connection diagram www.hglrc.com... -
Page 11: Vtx Serial Port Use. Vtx Uses Osd Smart Audio
2.Click have found UART1 Open the receiver serial port “ ” 10.VTX serial port use. VTX uses OSD smart audio 1.VTX connection diagram www.hglrc.com... - Page 12 2. DJI FPV Air Unit wiring 3.VTX serial port opens. The protocol is selected according to its own VTX protocol. 4. DJI serial port opens www.hglrc.com...
- Page 13 In the “Scr Layout” sub-menu, you can move the OSD elements (like battery voltage, mAh, and so forth) around on the screen. The “Alarms” sub-menu lets you control when the OSD will try to alert you that battery voltage is too low or mAh consumed is too high. www.hglrc.com...
-
Page 14: Gps Parameters Setting
The screen to the right shows the current vTX settings. From here, you can change the frequency band, channel, and power level of the video transmitter. After making the changes, move the cursor to “Set” and press roll-right to confirm the settings. 11. GPS parameters setting 1.GPS connection diagram www.hglrc.com... - Page 15 2.Open the GPS serial port 3.When using the GPS function, remember to configure the serial port (via the Ports tab). www.hglrc.com...
-
Page 16: Check Receiver Signal
12.Check receiver signal Check the remote control output signal 1.Click 13.Select flight mode startup mode 1.Click set up the function of remote control switch across the channel (below are for reference only) www.hglrc.com... -
Page 17: Osd Settings
14.OSD settings the OSD Settings, according to the need to choose, drag Click the OSD schematic diagram of the parameters can be adjusted. www.hglrc.com... -
Page 18: Led Settings
15.LED settings Click Turn on LED support 2.Click Click set according to need www.hglrc.com... -
Page 19: Troubleshooting
● Keep focus on the polarity. Check carefully before power supply. ● Cut off the power when you connect, plug and pull anything. ● The refresh rate of PID and Gyroscope is up to 8K/8K. www.hglrc.com... - Page 20 "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct www.hglrc.com...
Need help?
Do you have a question about the Veyron35 CR Pusher and is the answer not in the manual?
Questions and answers