Related Manuals for Horizon Hobby Blade Nano S3
Summary of Contents for Horizon Hobby Blade Nano S3
- Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di istruzioni...
- Page 2 Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
-
Page 3: Table Of Contents
Transmitter Batteries 4 AA Included Required Box Contents • Blade Nano S3 • 150mAh 1S 3.7V 45C Li-Po Battery (EFLB1501S45, RTF Only) • 1S USB Li-Po Charger, 300mA (EFLC1008, RTF Only) • MLP6DSM Transmitter (SPMRMLP6, RTF Only) • 4 AA Batteries (RTF Only) -
Page 4: Usb Charging Warnings
• Never connect the charger if the power cable damage. Please contact Horizon Hobby or an has been pinched or shorted. authorized retailer with compatibility questions. • Never attempt to dismantle the charger or use a damaged charger. -
Page 5: Transmitter Setup Table (Bnf)
Transmitter Setup Table (BNF) DX series, NX series, IX series SYSTEM SETUP FUNCTION LIST Model Type HELI Servo Setup Swash Type Normal Chan Travel Reverse Chan Travel Reverse 100/100 Normal 100/100 Normal F-Mode Setup 100/100 Normal 100/100 Normal Switch 1 Switch B 100/100 Normal... -
Page 6: Installing The Flight Battery
Dual Rate Selection (RTF transmitter) The control sensitivity can be changed by pressing and releasing the right control stick. The LED on the transmitter will show solid for high sensitivity (default) and flashing for low sensitivity. RTF Transmitter LED Indicator The transmitter LED gives a visual representation for various data. -
Page 7: Transmitter And Receiver Binding
0 position. If you encounter problems, refer to the troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Hobby Product Support office. Control Tests Ensure the throttle hold is ON when If the controls do not react as shown in the doing the direction control tests. -
Page 8: Understanding The Primary Flight Controls
Aileron Rear View Rear View Aileron left Aileron right Collective Pitch Left Side View Left Side View Collective pitch up Collective pitch down Understanding the Primary Flight Controls If you are not familiar with the controls of your Nano S3, take a few minutes to familiarize yourself with them before attempting your first flight. -
Page 9: Flight Modes
Aileron Rear View Rear View Left Right Aileron left Aileron right Flight Modes The Nano S3 RTF comes with the Blade • The model will NOT return to a level MLP6DSM transmitter. This transmitter has a attitude position when you release the flight mode switch that lets the pilot change controls. -
Page 10: Panic Recovery
Panic Recovery If you get into distress while flying in any • Move the collective stick to 50% and mode, push and hold the Bind/Panic Switch return all other transmitter controls to and move the control sticks to their neutral neutral for the quickest recovery. -
Page 11: Troubleshooting Guide
Low Voltage Cutoff (LVC) Landing LVC decreases the power to the motors To land, slowly decrease the throttle while when the battery voltage gets low. When in a low-level hover. After landing, discon- the motor power decreases and the red nect and remove the battery from the air- LED on the ESC flashes, land the aircraft craft after use to prevent trickle discharge. -
Page 12: Drift Calibration
To calibrate the Blade Nano S3: 1. After initialization, move the transmitter 4. Land the helicopter by slowly lowering sticks to the bottom, outside corners, as the throttle. -
Page 13: Exploded View And Parts Listings
Exploded View and Parts Listings... -
Page 14: Optional Parts
Part # Description 1 BLH01301 Flight Control: Nano S3 2 BLH2402 nCP S Main motor 3 BLH1302 Nano S2 Main plastic frame 4 BLH1304 Nano S2 Tail Fin 5 SPMSH2027L DSV40LBC-35 Servo *1 6 SPMSH2028L DSV40LBC-50 Servo *1 7 BLH1303 Nano S2 Canopy 8 BLH3302 Nano CP X Tail Boom and Motor... -
Page 15: Limited Warranty
Limited Warranty What this Warranty Covers the Product on which liability is asserted. As Horizon Hobby, LLC, (Horizon) warrants to the Horizon has no control over use, setup, final original purchaser that the product purchased assembly, modification or misuse, no liability (the “Product”) will be free from defects in... -
Page 16: Warranty And Service Contact Information
(Repairs and Repair Requests) com/RequestForm/ productsupport@ Horizon Product Support 2904 Research Rd horizonhobby.com (Product Technical Assistance) Champaign, Illinois 877-504-0233 61822 USA websales@horizonhobby. Sales 800-338-4639 Hanskampring 9 Horizon Technischer Service service@horizonhobby.eu D 22885 Barsbüttel, Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100 Germany... -
Page 17: Fcc Information
SPMRMLP6 Transmitter - Contains FCC ID: BRWWACO1T BNF Basic (BLH01350) includes Nano S3 Helicopter FCC ID: BRWWACO1T Supplier’s Declaration of Conformity Blade Nano S3 RTF/BNF (BLH01301/BLH01350) This device complies with part 15 communications. However, there is of the FCC Rules. Operation is... -
Page 18: Compliance Information For The European Union
Horizon Hobby, LLC Blade Nano S3 RTF/BNF 2904 Research Road (BLH01301/BLH01350); Champaign, IL 61822 USA Hereby, Horizon Hobby, LLC declares that the EU Importer of Record: device is in compliance with the following: Horizon Hobby, GmbH EU Radio Equipment Directive 2014/53/EU;... - Page 19 Blade, the Blade logo, E-flite, the BNF logo, DSM, DSM2, DSMX, Safe, the SAFE logo, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the Blade Nano S3 and is the answer not in the manual?
Questions and answers