Operation; Maintenance; Troubleshooting - IMER Mix-ALL Operating Manual

- Mix-ALL is fitted with an ac motor which must be connected
to a 220-230 V power supply with a cable fitted with suitable
wear-resistant, anti-crushing and weatherproof sheathing.
Cable length must not exceed 50 m.
- Mix-ALL must only be used when fitted with all required
safety devices, which must be in perfect working condition.
- Lay power cables where they are not subject to risk of
damage or penetration of water into the connectors.
- Only use connectors electrically protected against
water sprays. Do not stand the machine on the power cable.
- Never use the mixer with a makeshift power
connection.
-The electrical connection must be carried out by a
qualified technician.
- Ensure that the cable is securely clamped inside the plug and
socket.
- Observe all accident prevention and safety standards
in the work area.
- During mixer operation, do not insert tools or other objects in the
tank to avoid damage to the mixer or operator safety hazard.
10. START-UP
Press the green botton on the electrical system.
If the mixer blades do not rotate the overload cutout switch trips to
shut down the machine.

11. OPERATION

- Ensure that the power cable is fitted with a residual
current circuit breaker upline of the machine. If necessary,
use the quick coupling IMER residual current circuit breaker
available in kit form.
- Make sure that all other persons keep clear of the mixer during
operation.
- Switch the mixer off before leaving it unattended.
- Make sure that the mixer is completely immobile before handling
or installation.
- Make sure that the mains voltage corresponds with the
indications on the mixer data plate.
- Make sure that the mixer blades rotate clockwise.
- Make sure that no clothing comes into contact with
mixing blades.
- Warning: Never start the mixer without the safety grid
fitted; the cover is a safety device and must be fitted to avoid
direct contact with the mixer blades.
11.1 APPLICATIONS SUGGESTED
- Attention!! Don't leave fast setting materials inside the
machine longer than adviced by the product specifications.
11.1.1 ADHESIVES FOR CERAMIC TILES, FLOORING AND
WALL CLADDING
Pour in the quantity of water as required for the relative product,
considering that the maximum mixer capacity 50 kg of adhesive.
Start the machine and during operation, pour the powder directly
over the plastic cover to obtain a smooth mixture.
- Warning: when mixing large quantities, pour the
product into the tank gradually.
11.1.2 PAINT
IMER INTERNATIONAL S.p.A
Pour in the required amount of paint and water.
chemical products is strictly prohibited.
11.1.3 MORTARS (masonry/plaster)
Mix-ALL can also mix mortar, cement, or lime provided that a fine
particle size is used.
11.1.4 WATERPROOFING - REPAIR MORTARS
Pour in the quantity of water as indicated on the product
instructions, considering that the maximum mixer capacity is
25 liters.
11.1.5 SELFLEVELLING MORTAR
Pour in 3/4th of the water required by the product, then mix
until you reach a consistence "like plaster". Dilute the mixture
with the remaining water.
12. EMERGENCY STOP
mixer.
if the motor overheats the mixer is shut down automatically.
Allow the motor to cool before resuming operation.
13. CLEANING
After each work shift and before prolonged periods of disuse,
clean the tank interior and exterior thoroughly.
cleaning (also when using brushes, cloths or scrapers etc.).
- Avoid direct water sprays on the electric motor.

14. MAINTENANCE

the power supply before carrying out maintenance.
- Repairs to the electrical installation must be carried out
exclusively by qualified personnel. Replacement parts must be
original IMER spare parts and must not be modified in any way.
The IMER Mix-ALL is designed for minimum maintenance
requirements. In case the gearbox oil need to be refilled, please
use BLASIA P 3200 oil.
Check that the socket/plug contacts are clean. If oxidised, clean
immediately.
must be disposed of in accordance with the law.
machine are clearly legible.

15. TROUBLESHOOTING

PROBLEM
The motor does
not start when
10
- The use of acid, solvents, and other aggressive
- In an emergency, press the red button and unplug the
- The electric motor is protected from thermal overload;
- Always unplug the mixer from the mains before
- Never operate the mixer during cleaning operations.
- Do not use solvents or flammable liquids.
- Warning: Always switch off the mixer and unplug from
- Used oil is considered a special waste product and
- Always ensure that signs and warning notices on the
CAUSE
No power on power
cable
REMEDY
Check power cables