Daikin Altherma EPGA011-016DV Installer's Reference Manual page 94

2/10
Field settings table
Breadcrumb Field code Setting name
Room
└─ Antifrost
1.4.1 [2-06] Activation
1.4.2 [2-05] Room setpoint
└─ Setpoint range
1.5.1 [3-07] Heating minimum
1.5.2 [3-06] Heating maximum
1.5.3 [3-09] Cooling minimum
1.5.4 [3-08] Cooling maximum
Room
1.6 [2-09] Room sensor offset
1.7 [2-0A] Room sensor offset
Main zone
2.4 Setpoint mode
└─ Heating WD curve
2.5 [1-00] Low ambient temp. for LWT main zone heating WD curve.
2.5 [1-01] High ambient temp. for LWT main zone heating WD curve.
2.5 [1-02] Leaving water value for low ambient temp. for LWT main zone heating WD curve.
2.5 [1-03] Leaving water value for high ambient temp. for LWT main zone heating WD curve.
└─ Cooling WD curve
2.6 [1-06] Low ambient temp. for LWT main zone cooling WD curve.
2.6 [1-07] High ambient temp. for LWT main zone cooling WD curve.
2.6 [1-08] Leaving water value for low ambient temp. for LWT main zone cooling WD curve.
2.6 [1-09] Leaving water value for high ambient temp. for LWT main zone cooling WD curve.
Main zone
2.7 [2-0C] Emitter type
└─ Setpoint range
2.8.1 [9-01] Heating minimum
2.8.2 [9-00] Heating maximum
2.8.3 [9-03] Cooling minimum
2.8.4 [9-02] Cooling maximum
Main zone
2.9 [C-07] Control
2.A [C-05] Thermostat type
└─ Delta T
2.B.1 [1-0B] Delta T heating
2.B.2 [1-0D] Delta T cooling
└─ Modulation
2.C.1 [8-05] Modulation
2.C.2 [8-06] Max modulation
└─ Shut off valve
2.D.1 [F-0B] During thermo
2.D.2 [F-0C] During cooling
Additional zone
3.4 Setpoint mode
└─ Heating WD curve
3.5 [0-00] Leaving water value for high ambient temp. for LWT add zone heating WD curve.
3.5 [0-01] Leaving water value for low ambient temp. for LWT add zone heating WD curve.
3.5 [0-02] High ambient temp. for LWT add zone heating WD curve.
3.5 [0-03] Low ambient temp. for LWT add zone heating WD curve.
└─ Cooling WD curve
3.6 [0-04] Leaving water value for high ambient temp. for LWT add zone cooling WD curve.
3.6 [0-05] Leaving water value for low ambient temp. for LWT add zone cooling WD curve.
3.6 [0-06] High ambient temp. for LWT add zone cooling WD curve.
3.6 [0-07] Low ambient temp. for LWT add zone cooling WD curve.
4P556072-1 - 2018.12
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
0: Disabled
1: Enabled
4~16°C, step: 1°C
8°C
12~18°C, step: 0,5°C
12°C
18~30°C, step: 0,5°C
30°C
15~25°C, step: 0,5°C
15°C
25~35°C, step: 0,5°C
35°C
-5~5°C, step: 0,5°C
0°C
-5~5°C, step: 0,5°C
0°C
0: Fixed
1: WD heating, fixed cooling
2: Weather dependent
-40~5°C, step: 1°C
-10°C
10~25°C, step: 1°C
15°C
[9-01]~[9-00], step: 1°C
35°C
[9-01]~min(45, [9-00])°C , step: 1°C
25°C
10~25°C, step: 1°C
20°C
25~43°C, step: 1°C
35°C
[9-03]~[9-02]°C, step: 1°C
22°C
[9-03]~[9-02]°C, step: 1°C
18°C
0: Underfloor heating
1: Fancoil unit
2: Radiator
15~37°C, step: 1°C
25°C
[2-0C]=2:
37~60, step: 1°C
55°C
[2-0C]≠2:
37~55, step: 1°C
55°C
5~18°C, step: 1°C
8°C
18~22°C, step: 1°C
22°C
0: LWT control
1: Ext RT control
2: RT control
0: -
1: 1 contact
2: 2 contacts
3~10°C, step: 1°C
5°C
3~10°C, step: 1°C
5°C
0: No
1: Yes
0~10°C, step: 1°C
5°C
0: No
1: Yes
0: No
1: Yes
0: Fixed
1: WD heating, fixed cooling
2: Weather dependent
[9-05]~min(45,[9-06])°C, step: 1°C
35°C
[9-05]~[9-06]°C, step: 1°C
50°C
10~25°C, step: 1°C
15°C
-40~5°C, step: 1°C
-10°C
[9-07]~[9-08]°C, step: 1°C
8°C
[9-07]~[9-08]°C, step: 1°C
12°C
25~43°C, step: 1°C
35°C
10~25°C, step: 1°C
20°C
Installer setting at variance with
default value
Date Value
(*1) *6V_(*2) *9W_
(*3) *AB*_(*4) EAV*_
(*5) *X*_(*6) *H*_
(*7) EAV*18*_(*8) EAV*23*