Daikin Altherma EPGA011-016DV Installer's Reference Manual page 101

Field settings table
Breadcrumb Field code Setting name
9.I [9-00] What is the maximum desired LWT for main zone in heating?
9.I [9-01] What is the mimimum desired LWT for main zone in heating?
9.I [9-02] What is the maximum desired LWT for main zone in cooling?
9.I [9-03] What is the mimimum desired LWT for main zone in cooling?
9.I [9-04] Leaving water temperature overshoot temperature.
9.I [9-05] What is the mimimum desired LWT for add. zone in heating?
9.I [9-06] What is the maximum desired LWT for add. zone in heating?
9.I [9-07] What is the mimimum desired LWT for add. zone in cooling?
9.I [9-08] What is the maximum desired LWT for add. zone in cooling?
9.I [9-0C] Room temperature hysteresis.
9.I [9-0D] Pump speed limitation
9.I [9-0E] --
9.I [C-00] Domestic heating water priority.
9.I [C-01] --
9.I [C-02] Is an external backup heat source connected?
9.I [C-03] Bivalent activation temperature.
9.I [C-04] Bivalent hysteresis temperature.
9.I [C-05] What is the thermo request contact type for the main zone?
9.I [C-06] What is the thermo request contact type for the add. zone?
9.I [C-07] What is the unit control method in space operation?
9.I [C-08] Which type of external sensor is installed?
9.I [C-09] What is the required alarm output contact type?
9.I [C-0A] --
9.I [D-00] Which heaters are permitted if prefer. kWh rate PS is cut?
9.I [D-01] Contact type of preferential kWh rate PS installation?
9.I [D-02] Which type of DHW pump is installed?
9.I [D-03] Leaving water temperature compensation around 0°C.
9.I [D-04] Is a demand PCB connected?
9.I [D-05] Is the pump allowed to run if prefer. kWh rate PS is cut?
9.I [D-07] Is a solar kit connected?
9.I [D-08] Is an external kWh meter used for power measurement?
9.I [D-09] Is an external kWh meter used for power measurement?
9.I [D-0A] --
9.I [D-0B] --
9.I [E-00] Which type of unit is installed?
9.I [E-01] Which type of compressor is installed?
9.I [E-02] What is the indoor unit software type?
9.I [E-03] What is the number of backup heater steps?
(*1) *6V_(*2) *9W_
(*3) *AB*_(*4) EAV*_
(*5) *X*_(*6) *H*_
(*7) EAV*18*_(*8) EAV*23*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/O
R/W (*5)
R/O (*6)
R/O
(#) Setting is not applicable for this unit.
Range, step
Default value
[2-0C]=2:
37~60, step: 1°C
55°C
[2-0C]≠2:
37~55, step: 1°C
55°C
15~37°C, step: 1°C
25°C
18~22°C, step: 1°C
22°C
5~18°C, step: 1°C
8°C
1~4°C, step: 1°C
1°C
15~37°C, step: 1°C
25°C
[2-0D]=2:
37~60, step: 1°C
55°C
[2-0D]≠2:
37~55, step: 1°C
55°C
5~18°C, step: 1°C
8°C
18~22°C, step: 1°C
22°C
1~6°C, step: 0,5°C
1 °C
0~8, step:1
0 : No limitation
1~4 : 50~80%
5~8 : 50~80% during sampling
6
6
0: Solar priority
1: Heat pump priority
0
0: No
1: Bivalent
-25~25°C, step: 1°C
0°C
2~10°C, step 1°C
3°C
0: -
1: 1 contact
2: 2 contacts
0: -
1: 1 contact
2: 2 contacts
0: LWT control
1: Ext RT control
2: RT control
0: No
1: Outdoor sensor
2: Room sensor
0: Normally open
1: Normally closed
0
0: None
1: BSH only
2: BUH only
3: All heaters
0: No
1: Active open
2: Active closed
3: Safety thermostat
0: No
1: Secondary rtrn
2: Disinf. Shunt
0: No
1: increase 2°C, span 4°C
2: increase 4°C, span 4°C
3: increase 2°C, span 8°C
4: increase 4°C, span 8°C
0: No
1: Pwr consmp ctrl
0: Forced off
1: As normal
0: No
1: Yes
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0
2
0~5
0: LT split
1
0: Reversible (*5)
1: Heating only (*6)
3: 6V (*1)
4: 9W (*2)
9/10
Installer setting at variance with
default value
Date Value
4P556072-1 - 2018.12