Summary of Contents for Regency Fireplace Products I2404M
Page 1
Insert Owners & Installation Manual www.regency-fire.com MODELS: I2404M Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 919-032c 01.30.18...
Page 2
Thank-you for purchasing a REGENCY FIREPLACE PRODUCT. The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER in your area. Keep those REGENCY FIRES burning. “This wood heater has a manufacturer set minimum low burn rate that must not be altered.
SAFETY LABEL FOR I2404M This is a copy of the label that accompanies your Regency Insert. We have printed a copy of the contents here for your review. NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
installation Regency Inserts are constructed with the high- CHIMNEY 7) Circulating air chambers (i.e. in a steel est quality materials and assembled under strict fireplace liner or metal heat circulator) shall SPECIFICATIONS quality control procedures that insure years of not be blocked. trouble free and reliable performance.
installation OPTIONAL FLUE INSTALLING YOUR CONNECTOR KIT INSERT The Straight Flue Adaptor (Part #846-504) Your insert is very heavy and will require two shown here, may be used to produce a secure or three people to move it into position. The connection between your flue connector and the insert can be made a little lighter by removing insert collar.
installation MASONRY AND FACTORY BUILT FIREPLACE CLEARANCES The minimum required clearances to combustible materials when installed into a masonry or factory built fireplace are listed below. Unit Adjacent Mantle ** Side Minimum Minimum Minimum From Top of Side Wall (to Top) Facing Facing Hearth...
installation INSTALLATION INTO A FLUE CONNECTOR FACTORY BUILT BRACKET FIREPLACE Package contains: 3 brackets and 6 screws. 1) When installed in a factory built fireplace, a These brackets are to be used to hold the flue full stainless steel rigid or flexible flue liner is liner (not supplied) to the Insert and keep the mandatory, for both safety and performance connection.
installation 10 | STAINLESS STEEL SMOKE DEFLECTOR INSTALLATION The stainless smoke deflector is located in the upper front area of the firebox. The deflector is held in place with 2 bolts Prior to the first fire, ensure deflector is seated properly and secured with 2 hand tightened bolts. Smoke deflector installed with 2 bolts.
installation FACEPLATE AND TRIM INSTALLATION Faceplate side panel plates must be installed Note: It may be easier to install the insula- as follows: tion, faceplate top and faceplate trim with the unit pulled slightly away from the fireplace face. If this is done, be 1) Slide the spring nuts (supplied) over the very careful not to disturb the con- slots in the insert’s side convection panels...
installation 12 | FAN/BLOWER INSTALLATION Installer: Please record unit serial number here before installing blower. Serial No.______________________________ CAUTION: Label all wires prior 3) Ensure that the power cord is not in Your fan should only be installed once the unit is contact with any hot stove surfaces.
installation ensure the tube will not move when the unit DRAFT CONTROL is burning. Though there are four air tubes FLOOR PROTECTION in the medium units. Before establishing your first fire, it is important that your fully understand the operation of you Please check to ensure that your floor protection 2) Slide the left baffle over the air tubes from draft control.
operating instructions 14 | 13) Do not store any fuel closer than 2 feet from FIRST FIRE SOME SAFETY your unit. GUIDELINES When your installation is completed and in- 14) Do not burn salt drift wood as it will corrode spected, you are ready for your first fire.
operating instructions 9) During the first few hours it may be more ASH DISPOSAL CREOSOTE difficult to start the fire. As you dry out your fire brick and your masonry flue (if During constant use, ashes should be removed When wood is burned slowly, it produces tar and applicable), your draft will increase.
maintenance 16 | DOOR GASKET GLASS CLEANING If the door gasket requires replacement, 7/8" Only clean your glass window when it is cool. diameter material must be used. A proper high Your local retailer can supply you with special temperature gasket adhesive is required. A glass cleaner if plain water and a soft cloth does gasket repair kit, Part # 846-570 is available not remove all deposits.
MAIN ASSEMBLY & OPTIONS - I2404M Part # Description Part # Description Part # Description 850-152 Door Assy - Large Gold 42) 163-932 Convection Grill - Gold (Opt) 142-917 Fan Assembly 850-151 Door Assy - Large Black 163-930...
18 | FACEPLATES - I2404M Part # Description 140-911 Faceplate & Trim Set - Regular 180-570 Black Trim Regular (set of 3) 285) * Trim Right Regular 286) * Trim Top Regular 287) * Trim Left Regular 288) *...
BRICK PANELS - I2404M Part # Description 180-960 Firebrick - Complete Set 70) 902-111 Brick Regular Full Size: 1-1/4" x 4-1/2" x 9" 75) * Brick Partial: 1-1/4 x 4-1/2" x 2" 76) * Brick Partial: 1-1/4" x 2" x 9"...
warranty 20 | Limited Lifetime Warranty FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Lifetime Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below.
Page 21
warranty All warranty claims must be submitted by the dealer servicing the claim, including a copy of the Bill of Sale (proof of purchase by you). All claims must be complete and provide full details as requested by FPI to receive consideration for evaluation.
Page 22
warranty 22 | Limitations of Liability: The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY.
Page 23
warranty Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
Need help?
Do you have a question about the I2404M and is the answer not in the manual?
Questions and answers