Antunes 9210875 Owner's Manual
  1. Manuals
  2. Brands
  3. Antunes Manuals
  4. Toaster
  5. 9210875
  6. Owner's manual

Antunes 9210875 Owner's Manual

Gold standard toaster
Hide thumbs
Table of Contents

Advertisement

Quick Links

GST-3V
Gold Standard Toaster
owner's manual
Manufacturing Numbers:
9210875
www.antunes.com
P/N 1011190 Rev. G 01/17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9210875 and is the answer not in the manual?

Questions and answers

Related Manuals for Antunes 9210875

Summary of Contents for Antunes 9210875

  • Page 1 GST-3V Gold Standard Toaster owner’s manual Manufacturing Numbers: 9210875 www.antunes.com P/N 1011190 Rev. G 01/17...

  • Page 2: Table Of Contents

    Notes facturer will void the warranty. Limited Warranty IMPORTANT A.J. Antunes & Co. reserves the right to change specifications and product de- sign without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

  • Page 3: Important Safety Information

    IMPORTANT SAFETY WARNINGS INFORMATION Be advised of the following warnings when operating and performing mainte- Use the following guidelines for safe op- nance on this unit. eration of the unit. If the supply cord is damaged, it Read all instructions be- must be replaced by the manu- fore using equipment.

  • Page 4: Specifications

    Model & Width Height Height Mfg. No. 30” (762 mm) GST-3V 22 1/2" (572 mm) 25" (635 mm) 16 1/2" (419 mm) 9210875 (without Bun Feeder) (with Bun Feeder) Model & Plug Volts Watts Hertz Mfg. No. Description NEMA 6-20P...

  • Page 5: Installation

    • Owner’s Manual Finished product drops into the bun NOTE: If any parts are missing or dam- landing zone. aged, contact Antunes Techni- Light/Dark Adjustments cal Service IMMEDIATELY at 1-877-392-7854 or 1-630-784- The light/dark value can be adjusted when 1000.

  • Page 6: User Mode

    USER MODE Fault Messages To adjust the Front Heater Setpoint Temperature, press the LIGHTER The unit displays fault messages when or DARKER buttons to reach the User Mode allows an operator to view the there is a problem with the unit. toaster settings but does not permit any desired temperature.

  • Page 7: Daily Cleaning

    DAILY CLEANING 11. Reinstall the Front and Rear Con- To lock out the front Conveyor veyor Covers and then re-install Roller, face the front of the toaster. Turn the toaster’s power switch to the Bun Feeder and Butter Wheel Use both hands and push down on the off position.

  • Page 8: Cleaning The Top Cooling Fan And Electrical Housing (Annually)

    Re-engage the Upper Belt Frame Lock by lifting up and then locking it in place on the Front Conveyor Assembly. Close and latch the Side Panel. NOTE: Inform the Store Manager after any Belt Replacement so new Belts can be ordered. To obtain new Belts, contact the factory at 1-877-392-7854 (North America only) or 630-784-1000.

  • Page 9: Troubleshooting

    TROUBLESHOOTING Problem Possible Cause Corrective Action Control Display flashes FPLt Front Platen temperature is below 515° F (268° Allow the unit to warm up for 30 minutes and then recheck. If the Control Display still flashes FPLt, contact your maintenance person continuously.
  • Page 10 TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action Buns not toasting adequately. Compression Setting is incorrect. Use the recommended setting of 4. One of the Conveyor top shafts is stuck in the Inspect positions of the shafts as described in the Maintenance lower lock position.

  • Page 11: Replacement Parts

    REPLACEMENT PARTS (continued) Item Part # Description QTY. 0012891 Butter Wheel Assembly (Incl Items 2, 3, and 4) 0021850 Butter Wheel Weldment 0012890 Scraper Assembly 0506496 Butter Tray P/N 1011190 Rev. G 01/17...
  • Page 12 REPLACEMENT PARTS (continued) NOTE (See Page 15 for Detail) Item Part # Description QTY. Item Part # Description QTY. 0506514 Cover, Fixed Platen 0021837 Weldment, Drive Roller Adjust 310P214 Screw, Hex #10-32 X 1/2” Platen 0506525 Support Bracket, RH 325P193 Screw, Hex Head, #1/4-20 X 1.375”, S.S.
  • Page 13 REPLACEMENT PARTS (continued) Item Part # Description QTY. Item Part # Description QTY. 2100212 Handle, Pocket Pull, Snap-In 2100334 Thrust Strip 0506492 Back Conveyor Cover 3000123 Ring, Retaining, External 0506518 Front Conveyor Cover 325P193 Screw, Hex Head, #1/4-20 X 1.375”, S.S. 1 0506519 End Housing Door 2120217...
  • Page 14 REPLACEMENT PARTS (continued) Item Part # Description Qty. Item Part # Description Qty. Item Part # Description Qty. 1001505 Label, Control 4060398 Terminal Block, S-Series 2100345 Thrust Strip Rh Cam 7000965 Control Board Kit 2120233 Spacer .252 Id X .5 Od X .925” Lg 0600156 Spring, Cam Adjustment 304P105...

  • Page 15: Replacement Part Kits

    REPLACEMENT PARTS (continued) Item Part # Description Qty. Item Part # Description Qty. Item Part # Description Qty. 3000123 Ring, Retaining, External 2150312 Sprocket, 25B14, .498” Bore 0506144 Plate, Tensioner Rh 2120221 Spacer, 0.69 X 0.503 X 0.359 0506185 Bracket, Chain Tensioner 0506162 Bracket, Bearing Rh 0504320...
  • Page 16 REPLACEMENT PARTS (continued) (2X) 14 & 12 12 & 14 Item Part # Description QTY. Item Part # Description QTY. Item Part # Description QTY. 3100101 Hex, Nut #10-32 0021815 Weldment, Back Plate Adj. Platen 0506083 Spacer .075 THK .203 ID x .312 OD 3100125 Screw, Mach.

  • Page 17: Wiring Diagram

    WIRING DIAGRAM P/N 1011190 Rev. G 01/17...

  • Page 18: Notes

    NOTES P/N 1011190 Rev. G 01/17...
  • Page 19 NOTES (continued) P/N 1011190 Rev. G 01/17...

  • Page 20: Limited Warranty

    Travel Time & Mileage in excess of 2 hours (100 miles/160 km) round trip from the nearest authorized service agency. A.J. Antunes & Co. reserves the right to make changes in design or add any improvements on any product. The right is al- ways reserved to modify equipment because of factors beyond our control and government regulations.

This manual is also suitable for:

Gst-1hGst-3v

Table of Contents