Dahua Technology A21BC0V Quick Start Manual

Dahua Technology A21BC0V Quick Start Manual

2 mp hdcvi vari-focal bullet camera

Advertisement

Quick Links

2 MP HDCVI Vari-focal Bullet Camera
A21BC0V
Quick Start Guide
Version 1.0.1
Dahua Technology USA Inc.

Advertisement

Table of Contents
loading

Summary of Contents for Dahua Technology A21BC0V

  • Page 1 2 MP HDCVI Vari-focal Bullet Camera A21BC0V Quick Start Guide Version 1.0.1 Dahua Technology USA Inc.
  • Page 2: Table Of Contents

    Table of Contents Welcome........................1 Important Safeguards and Warnings ..............1 Electrical safety ....................1 Environmental Precautions ................2 Operation and Daily Maintenance ..............3 Warnings ......................3 FCC Information ....................4 FCC compliance: .................... 4 Legal Notices ....................4 Copyright ......................
  • Page 3: Welcome

    1 Welcome This manual offers reference material and general information about the basic operation, maintenance, and troubleshooting of the Dahua Multi-Sensor Panoramic Camera. Read, follow, and retain the following safety instructions. Heed all warning on the unit and in the operating instructions before operating the unit.
  • Page 4: Environmental Precautions

    • If the unit is damaged and requires service, unplug the unit from the main AC power supply and from the PoE supply and refer to qualified service personnel. Damage may include, but is not limited to: • The power supply cord or plug is damaged. •...
  • Page 5: Operation And Daily Maintenance

    Operation and Daily Maintenance • Do not touch the heat dissipation component of the unit. This part of the unit is hot and may cause a burn. • Do not open or dismantle the device; there are no components that a user can fix or replace. Opening the unit may cause water leakage or expose components to direct light.
  • Page 6: Fcc Information

    1.3 Legal Notices Copyright This user guide is ©2017, Dahua Technology Company, LTD. This user guide is the intellectual property of Dahua Technology Company, LTD and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
  • Page 7: Unpacking

    2 Unpacking This equipment should be unpacked and handled with care. If an item appears to have sustained damage during shipping, notify the shipper immediately. Verify that all the parts listed below are included. If an item is missing, contact customer support or your local representative.
  • Page 8: Installation And Configuration

    3 Installation and Configuration 3.1 Camera and Cables Figure 3-1 Port Name Connector Function Video Out HDCVI or Analog Video Output Power port, input 12 VDC or 24 VAC. Note: • Please connect the default DC5.5 round port to the 2-pin Power Input Port converter cable when you are using 24 VAC power.
  • Page 9: Device Installation

    4 Device Installation This section details installing the camera to a wall or to a ceiling. Note that the wall or ceiling must be capable of supporting a minimum of three times the weight of the camera and a bracket (if used). DO NOT connect the camera to the power supply during installation.
  • Page 10 6. Insert a self-tapping screw into each hole on the camera base and secure to an expansion bolt. 7. Connect the external cables from the camera to the appropriate cables for Ethernet and power. 8. Supply power to the camera. 9.
  • Page 11: Adjusting The Focal Length

    4.2 Adjusting the Focal Length Figure 4-3 1. Remove the two pan head screws and remove the panel from the underside of the camera. 2. Adjust the lens focus control until the scene is in focus. 3. Replace the lower cover and secure it to the camera with the two (2) pan head screws.
  • Page 12 5 Setting Camera Parameters HDCVI technology allows you to set parameters for the camera and to control the camera from a Dahua HDCVI DVR. 1. Connect the camera to a Dahua HDCVI DVR. 2. From the DVR, select the Main Menu and choose Setting. Then, select the System tab and select the PTZ link, on the left-side menu.
  • Page 13 10. Click the Camera icon to access the Operation Menu. Figure 5-3 11. Use the following table to access the camera’s menu: Button Function Access the camera’s settings menu. Select a menu item. Select a setting value. Adjust lens zoom and auto trigger function. Adjust lens focus.
  • Page 14 Dahua Technology USA Inc. 23 Hubble, Irvine, CA 92618 Tel: (949) 679-7777 Fax: (949) 679-5760 Email: sales.usa@global.dahuatech.com Rev 001.001 © 2017 Dahua. All rights reserved. Design and specifications are subject to change without notice.

Table of Contents