Related Manuals for Seagate ST6000NE0001
Summary of Contents for Seagate ST6000NE0001
- Page 1 Enterprise NAS HDD SATA Product Manual ST8000NE0001 ST6000NE0001 100780707, Rev. A November 2015...
- Page 2 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Power Choice and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
-
Page 3: Table Of Contents
Seagate® Technology Support Services ........ -
Page 4: Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery- services/ For Seagate OEM, Distribution partner portal and reseller portal, visit: http://www.seagate.com/partners Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 5: Introduction
Introduction Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® Enterprise NAS HDD model drives:. Standard 512e models ST8000NC0002 & ST6000NC0002 These drives provide the following key features: • 7200 RPM spindle speed. • PowerChoice™ for selectable power savings •... -
Page 6: Drive Specifications
–304.8 m to 12,192 m (below mean sea level, max) (–1000 ft to 40,000+ ft) Read 70 Gs Operational Shock (max at 2 ms) Write 40 Gs Non-Operational Shock (max at 2 ms) 250 Gs Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 7: Formatted Capacity
Spindle speed (RPM) (± 0.2%) 7200 Internal data transfer rate (Mb/s max) 2546 Sustained data transfer rate (max) 237 MiB/s (249 MB/s) I/O data-transfer rate (MB/s max) 600 (Ultra DMA mode 5) Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 8: Start/Stop Times
Maximum DC 0.46 0.62 Maximum DC (peak) 0.57 1.03 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 9: Conducted Noise
5V ± 5% 12V ± 5% 2.5.4 Extended Power Conditions - PowerChoice Utilizing the load/unload architecture a programmable power management interface is provided to tailor systems for reduced power consumption and performance requirements. Seagate Enterprise NAS HDD Product Manual, Rev. A... - Page 10 • Saved enabled state, and timer value • Current enabled state, and timer value S.M.A.R.T. Read Data Reports • Attribute 192 - Emergency Retract Count • Attribute 193 - Load/Unload Cycle Count Seagate Enterprise NAS HDD Product Manual, Rev. A...
- Page 11 Disable EPC Feature Set PowerChoice Supported Extended Power Condition Identifiers Power Condition Identifiers Power Condition Name Standby_z 01 - 80 Reserved Idle_a Idle_b Idle_c 84 - FE Reserved All EPC Power Conditions Seagate Enterprise NAS HDD Product Manual, Rev. A...
-
Page 12: Environmental Limits
Non-operating –40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. HDA Temp. -
Page 13: Shock
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 10–500 Hz 4.9 Grms ref Linear Random Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 14: Acoustics
Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 15: Reliability
EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. -
Page 16: Fcc Verification
Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 17: Environmental Protection
Drive specifications 2.12 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.12.1 European Union Restriction of Hazardous Substances (RoHS) Directive The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. -
Page 18: Corrosive Environment
Seagate’s option and at no charge to the customer, if returned by customer at customer’s expense to Seagate’s designated facility in accordance with Seagate’s warranty procedure. -
Page 19: Configuring And Mounting The Drive
• The screws should be inserted no more than 0.140 in (3.56mm) into the bottom or side mounting holes. • Do not overtighten the mounting screws (maximum torque: 6 in-lb). • Do not cover breather hole on top cover. Figure 4. Breather hole location - top cover Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 20: Mechanical Specifications
SFF-8301 and SFF-8323, found at www.sffcommittee.org The images below are for mechanical tolerance reference only and Note may not be a visual representation of the actual drive. Figure 5. Mounting dimensions—top, side and end view Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 21: Serial Ata (Sata) Interface
Power 5V power 5V power Ground 2nd mate Ground or LED signal If grounded, drive does not use deferred spin Ground 1st mate. 12V power, pre-charge, 2nd mate 12V power 12V power Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 22: Supported Ata Commands
Read DMA Extended Read FPDMA Queued Read Log DMA Ext Read Log Ext Read Multiple Read Multiple Extended Read Sectors Read Sectors Extended Read Sectors Without Retries Read Verify Sectors Read Verify Sectors Extended Seagate Enterprise NAS HDD Product Manual, Rev. A... - Page 23 Write DMA FUA Extended Write FPDMA Queued Write Log DMA Ext Write Log Extended Write Multiple Write Multiple Extended Write Multiple FUA Extended Write Sectors Write Sectors Without Retries Write Sectors Extended Write Uncorrectable Seagate Enterprise NAS HDD Product Manual, Rev. A...
-
Page 24: Identify Device Command
LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature. Retired 0000 Multiword DMA active and modes supported (see note following this table) xx07 Seagate Enterprise NAS HDD Product Manual, Rev. A... - Page 25 NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support. 112–118 ATA-reserved 0000 Commands and feature sets supported 41DE Commands and feature sets supported or enabled 40DC 121-127 ATA-reserved 0000 Security status 0021 129–159 Seagate-reserved xxxx Seagate Enterprise NAS HDD Product Manual, Rev. A...
- Page 26 Ultra DMA mode 0 is supported. Ultra DMA mode 1 is supported. Ultra DMA mode 2 is supported. Ultra DMA mode 3 is supported. Ultra DMA mode 4 is supported. Ultra DMA mode 5 is supported. Seagate Enterprise NAS HDD Product Manual, Rev. A...
-
Page 27: Set Features Command
Disable use of SATA features Enable read look-ahead (read cache) feature (default). Report full capacity available At power-on, or after a hardware or software reset, the default values of the features are as indicated above. Note Seagate Enterprise NAS HDD Product Manual, Rev. A... -
Page 28: Commands
S.M.A.R.T. Enable Operations S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status If an appropriate code is not written to the Features Register, the Note command is aborted and 0x04 (abort) is written to the Error register. Seagate Enterprise NAS HDD Product Manual, Rev. A... - Page 29 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100780707, Rev. A...