Page 2
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com...
Toll-Free: 800-775-0703 or customerservice@kraususa.com The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a licensed professional.
Parts List KWU210-57 · Cut-Out Template Mounting Hardware · · Bottom Grid KBG-WSU2-57 Bottom Grid KBG-WSU1-45 · · Strainer ST-1 · Drain Cap STC-2 Accessories Board KAB-105BB · · Cutting Board KCB-WS104BB · Dish Rack KDR-1 · Colander KCL-2 · Serving Bowl KBW-2 Rolling Mat KRM-11BL ·...
Page 5
Step 1. Check the Template · Check the template against the sink for accuracy. KRAUS Recommended Installation Type 55" (1397mm) 1/2" Positive Reveal Zero Reveal Zero Reveal 1/2" Positive Reveal 1/2" Positive Reveal Zero Reveal 1/2" The countertop meets the edge of the sink The countertop edge sits approximately 1/2"...
Page 6
Step 2. Position Template · Check the cut-out template against the actual sink to ensure a proper sized cut-out. · Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Page 7
Step 3. Trace Template Trace template on countertop with a pencil. ·...
Page 8
Step 4. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
Page 9
Step 5. Set up Mounting Brackets • Turn countertop over and align sink with countertop. Decide location for mounting brackets. • Mounting holes should be 1/2" from edge of sink. 1/2" (13mm) Step 6. Drill Hole in Countertop • Drill 3/8" diameter x 1/2" deep hole in the countertop.
Page 10
Step 7. Install Anchors • Insert anchors into drilled holes and lightly tap with a hammer until flush. Step 8. Secure Sink to Countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop.
Step 9. Attach Mounting Hardware • Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. • Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant. Step 10. Install Plumbing Fixtures ·...
Page 12
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable to a subsequent owner.
Page 13
Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com...
Page 14
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...