Ganz ZN-S1000VE Hardware Manual
1ch h.264 encoder
Hide thumbs
Also See for ZN-S1000VE:
- Quick installation manual (5 pages) ,
- Hardware manual (20 pages) ,
- Installation manual (21 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ganz ZN-S1000VE
Summary of Contents for Ganz ZN-S1000VE
- Page 1 ZN-S100V/ZN-S1000VE HARDWARE MANUAL 2010/2-1 D1A.02 ...
-
Page 2: Table Of Contents
ZN-S100V/ZN-S1000VE HARDWARE MANUAL Table of Contents 1. Introduction......................3 2. Product Description ....................4 2.1. Function specification ....................4 3. Installation & Configuration ..................6 3.1. Package contents...................... 6 3.2. Components ......................7 3.2.1. Front Panel ........................7 3.2.2. Rear Panel ........................9 3.3. Basic Connection ....................13 3.4. Serial Number / MAC Address................14 4. Operation Description.................... 15 4.1. Factory Default Settings ..................15 4.2. Rebooting ....................... 15 5. Power over Ethernet (PoE) .................. -
Page 3: Introduction
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 1. Introduction ZN‐S100V and ZN‐S1000VE are encoder module. ZN‐S100V/ZN‐S1000VE compress video/audio data and transmit the compressed video/audio data through the network in real time. ZN‐S100V/ZN‐S1000VE provides a high quality video image with a limited bandwidth and storage capacity. ZN‐S100V/ZN‐S1000VE also supports dual stream mode, ... -
Page 4: Product Description
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 2. Product Description 2.1. Function specification ZN‐S100V/ZN‐S1000VE series specification is shown as following Table. ZN‐S100V/ZN‐S1000VE series Item ZN‐S100V ZN‐S1000VE Number of Streams Dual Stream, Configurable Input channel 1ch Output Channel 1 Loop Out Compression H.264, MPEG‐4, MJPEG Selectable per Stream Resolution D1, 4CIF, CIF, QCIF, VGA, QVGA Compression FPS 25/30fps@D1 (PAL/NTSC) Input / Output Not available 1/1ch Data Format Not available PCM & G.711 Network 10/100 Base‐T DI/DO Not available 2/2 RS‐232C ... - Page 5 ZN-S100V/ZN-S1000VE HARDWARE MANUAL On‐screen Display Real‐time Display of Tracking Data and Events VCA Surveillance (Optional) Direction, Stopping, Loitering, Entering, Exiting, Appear, and Detection Behavior Disappear Filters 3D Behavior Perspective Corrected Size and Speed Filters Statistics Counting Functions and Other Statistics Meta Data Binary XML Format Image Stabilization (Optional) Electronic Stabilization Removes Camera Sway 2010/2-1 D1A.02 ...
-
Page 6: Installation & Configuration
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 3. Installation & Configuration 3.1. Package contents The Package contains the following. Please make sure all listed items are included in the box. ZN‐S100V or ZN‐S1000VE ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 1 LAN Cable (Cross type 1m) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 1 9port Terminal block plug (except ZN‐S100V) ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐2 DC 12V Power Adapter‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐1 AC100~AC240V power cable‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 1 2010/2-1 D1A.02 ... -
Page 7: Components
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 3.2. Components 3.2.1. Front Panel ③ ④ ① ⑤ ② Figure 1. Front Panel of ZN‐S1000VE ① ② ⑧ ⑥ ⑦ Figure 2. Front Panel of ZN‐S100V ① Video Input BNC Connector (Vin 1) It is mainly used for video inputs. ② Video Output BNC Connector This connector is used for loop‐out of video input. ③, ④ Indicator LED (Status, Data) Status and Data indicators display the following system information. Status LED has a yellow, a green and an orange color. Data LED has a red, a green and a dark orange color. 1. Power off Item Status Data ... - Page 8 ZN-S100V/ZN-S1000VE HARDWARE MANUAL 2. System initialization Item Status Data In Process Off Blinking Dark Orange Normal State Orange Off Abnormal State Orange Dark Orange 3. Kernel booting up Item Status Data In Process Orange Green Normal State Orange Off Abnormal State Orange Green 4. Video streaming service Item Status Data Normal Blinking Green Off Abnormal Green ...
-
Page 9: Rear Panel
ZN-S100V/ZN-S1000VE HARDWARE MANUAL Figure 4. Power Connection ⑧ Reset Switch (Reset) Reset switch is used for restarting ZN‐S100V/ZN‐S1000VE or resetting ZN‐S100V/ZN‐ S1000VE as Factory Default (FD). Refer to ‘4.1. Factory Default Settings’ for detailed procedures. 3.2.2. Rear Panel ② ① ⑤ ④ ... - Page 10 ZN-S100V/ZN-S1000VE HARDWARE MANUAL Figure 6. Terminal block 1. Audio Input ZN‐S1000VE has one channel mono audio input. 2. Audio Output ZN‐S1000VE has one channel mono audio output. As the output power for the audio is low, amplifier speaker is needed (Do not use a headphone or earphone directly to the camera). 3. Digital Input (DI1, DI2) ZN‐S1000VE supports two digital inputs. It can be connected either voltage type sensor or relay type sensor as following Figure 7. and Figure 8. Do not use voltage and relay type sensor together. Please pay attention to electric characteristics during installation. (Detailed instructions are being prepared.) ch1 Sensor 1 ch2 Sensor 2 1 2 Figure 7. Voltage Type Digital Input Connection ch1 Sensor 1 ch2 Sensor 2 1 2 ...
- Page 11 ZN-S100V/ZN-S1000VE HARDWARE MANUAL Please pay attention to electric characteristics during installation. (Detailed instructions are being prepared.) ch1 LED 1 +12V ch2 LED 2 1 2 Figure 9. Digital Output Connection 5. RS‐485 The RS‐485 serial port consists of DATA+, DATA‐ and GND as following Figure 10. DATA+ DATA+ DATA‐ DATA‐ PTZ Camera + ‐ Figure 10. RS‐485 Connection 6. RS‐232C RS‐232C Terminal Block is used for some devices such as POS terminal block. RX TX RX TX Figure 11. RS‐232C Connection ...
- Page 12 ZN-S100V/ZN-S1000VE HARDWARE MANUAL ④ Power Adaptor Connector (DC 12V) ZN‐S1000VE needs a DC 12V 1A adapter for power supply. ‐ Figure 12. Power Connection ⑤ Reset Switch (Reset) Reset switch is used for restarting ZN‐S100V/ZN‐S1000VE or resetting ZN‐S100V/ZN‐ S1000VE as Factory Default (FD). Refer to ‘4.1. Factory Default Settings’ for detailed procedures. 2010/2-1 D1A.02...
-
Page 13: Basic Connection
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 3.3. Basic Connection SD memory Camera External Monitor Figure 13. ZN‐S1000VE’s Front Panel Connection Sensor 1‐2 USB memory DC Adapter LAN Amp Speaker Alarm PTZ Camera Figure 14. ZN‐S1000VE’s Rear Panel Connection Normal operation may not be possible if temperature or humidity exceed levels recommended in the ZN‐S100V/ZN‐S1000VE specification. 2010/2-1 D1A.02 ... -
Page 14: Serial Number / Mac Address
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 3.4. Serial Number / MAC Address Serial number and MAC address is attached on the bottom as shown in Figure 15. MAC 00:1C:B8:C0:14:B1 550012345 MAC Address ZN-S1000VE P1331010100000-121 Serial Number Figure 15. Serial Number/ MAC Address 2010/2-1 D1A.02 ... -
Page 15: Operation Description
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 4. Operation Description 4.1. Factory Default Settings Factory default settings are as follows: • IP address: 192.168.xx.yy (Refer to 2.3 Serial Number / MAC Address) • Mask: 255.255.0.0 • Gateway: 192.168.0.1 • User ID: root • Password: pass MAC address = 00‐1C‐B8‐C0‐14‐B1 → IP address = 192.168.35.69 Convert the Hexadecimal number to Decimal number To perform the FD (Factory Default) initialization: ZN‐S1000VE Refer to ‘Figure 1.’ Turn off the power. Press and hold the Reset button Turn on the power. Release the Reset button when the Status LED’s color is orange and the Data LED’s color is red. Wait for the system to reboot. ... - Page 16 ZN-S100V/ZN-S1000VE HARDWARE MANUAL 1. Press Reset. The red Data LED will blink several times. When Reset function is activated, the red Data LED will turn on. User may stop pressing Reset at this point. 2. When “Reset” function has been completed, the green Data LED will turn on and Status LED and Data LED will blink together. ZN‐S100V Refer to ‘Figure 2’ and ‘Figure 3’ 1.While the camera is in use, press and hold the Reset button. (Both the Status and Network LEDs are on.) 2.Release the Reset button after 3 seconds. 2010/2-1 D1A.02 ...
-
Page 17: Power Over Ethernet (Poe)
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 5. Power over Ethernet (PoE) The PoE module used in ZN‐S100V/ZN‐S1000VE is commercially available module without modification. The standard ZN‐S100V/ZN‐S1000VE does not include PoE module in it. PoE module is included on the request of a customer. For the detailed information, please ... -
Page 18: Electrical Characteristics
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 6. Electrical characteristics 6.1. Operating conditions Parameters Min Typical Max Units Video Peak to peak amplitude 0.25 1 2 V input range Sync amplitude 72 286 572 mV ±7 Horizontal lock range ‐ ‐ % of line length ±800 Color sub‐carrier Lock‐ ‐ ‐ ... -
Page 19: Dimensions
ZN-S100V/ZN-S1000VE HARDWARE MANUAL 7. Dimensions ZN‐S100V 94.6 74.6 106.6 26.3 Unit : mm 2010/2-1 D1A.02 ... - Page 20 ZN-S100V/ZN-S1000VE HARDWARE MANUAL ZN‐S1000VE 141.4 121.7 37.7 103.4 1CH Encoder RS-232 Rx Tx DC12V Status Data Vout Reset Ethernet Aout RS-485 Unit : mm 2010/2-1 D1A.02 ...