Advertisement
ZN-S100V
This manual has been designed to guide you through basic settings of your IP devices, such as installation and
configuration for using them.
Step1. Connect cables to IP device
Connect each cable to the device. To see the correct positions of all connectors, refer to the following image
below.
Step2. Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the
MAC address of your device. Please make sure the device and your PC are on the same network segment
before running the installation. If the network segment was different between your PC and the device, change
your PC's settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
2010/2‐1
Quick Installation Guide
VIN
RESET Button
LAN
DC 12V
* Models herein and their appearance
are subject to change without any prior
notice.
1
Advertisement
Table of Contents
Related Manuals for Ganz ZN-S100V
Summary of Contents for Ganz ZN-S100V
- Page 1 ZN-S100V Quick Installation Guide This manual has been designed to guide you through basic settings of your IP devices, such as installation and configuration for using them. Step1. Connect cables to IP device Connect each cable to the device. To see the correct positions of all connectors, refer to the following image below. VIN RESET Button LAN * Models herein and their appearance are subject to change without any prior notice. DC 12V Step2. Set up network environment The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the ...
- Page 2 STEP3. View video on web page View the live video on a web page using your IP device and its IP address. To have the correct IP address ready and use it on a web page: Convert a MAC address to an IP address. (The MAC address is attached on the side or bottom of the device.) MAC address = 00‐13‐23‐01‐14‐B1 → IP address = 192.168.20.177 the Hexadecimal number to Decimal number. Open a web browser and enter the IP address of the device. Click Continue to this website (not recommended) as below. (The explanation and captured images at this manual are mainly on the basis of Internet Explorer 7.0) ...
- Page 3 Wait for a few seconds while the web page loads. The live video is displayed as below. If the live video is not displayed and “Can not Create XMLDOMDocument Install MSXML4.0” message is shown as below, please download and Install from the link below. http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B‐B4F2‐46DA‐B4B6‐ C5D7485F2B42&displaylang=en (VCA Library requires MS XML 4.0 library which is an xml parser made by Microsoft.) 2010/2‐1 3 ...
- Page 4 Step4. Setting IP Address To set up the Network configuration: Click Setup on the upper right of the web page. The login page is displayed as below. Enter the default user name (root) and the default password (pass), and then select OK. The default username and password are: root and pass. Click System Options, and then select TCP/IP from the drop‐down menu. To change the IP address, please make sure to check and have the correct Subnet mask and Gateway ready. To use DHCP, select Obtain an IP address via DHCP. To learn how to set up the web page for advanced configuration, refer to the Web Page User's Manual, which is available on the SDK at the following path. {SDK root}\DOC\ 2010/2‐1 4 ...
-
Page 5: Resetting To The Factory Default Settings
Advanced setup (ZNS-GIT IPAdmin Tool) ZNS‐GIT IPAdmin Tool is a utility program for IP products. Following list shows a part of features that ZNS‐GIT IPAdmin Tool provides. Configure IP address, Subnet mask and Gateway Shows network related information such as MAC address Updates firmware Reboots the device ZNS‐GIT IPAdmin Tool is provided with SDK at the following SDK path. {SDK root}\BIN\TOOLS\AdminTool\ Rebooting Reset can be carried out as follows: 1. While the device is in use, press and hold the Reset. 2. Release the Reset button after 3 seconds. 3. Wait for the system to reboot. Resetting to the Factory Default Settings This will reset all parameters, including the IP address, to the Factory Default initialization. To perform the Factory Default settings: 1. Disconnect the power supply from the device. 2. Connect the power to the device with the Reset button pressed and held. 3. Release the Reset button after 5 seconds. 4. Wait for the system to reboot. ...
Need help?
Do you have a question about the ZN-S100V and is the answer not in the manual?
Questions and answers