Table of Contents
Advertisement
MODBUS I/O ASSIGNMENTS
Coil (0X)
Inputs (1X)
1025 – 1040
1041 – 1056
1057 – 1072
Input Registers (3X)
Holding Registers (4X)
I: Integer, 0 – 10000 (0 – 100%)
F: Floating (32-bit data cannot be accessed using floating addresses.)
Note: DO NOT access addresses other than mentioned above. Such access may cause problems such as inadequate operation.
• Module Status indicates whether individual I/O modules are mounted or not. The bit corresponding to the mounted slot
turns to "1," and the unmounted slot to "0."
• Error Status indicates error status for each module as described below. The bit corresponding to such module turns to "1."
R3-TSx, R3-RSx, R3-US4: Input burnout
R3-DA16A: Power input in error or disconnected
R3-YSx: Output current error (e.g. load unconnected)
R3-PC16A: External power supply in error or disconnected
• Data Error Status indicates overrange (R3-US4: out of -10% to +110%; the other types: out of -15% to +115%) status for each
module. The bit corresponding to such module turns to "1."
• Main / Sub Switching Commands given to the network modules result as follows:
'MAIN' MODULE
'SUB' MODULE
1
0
1
0
TRANSMISSION DATA ASSIGNMENTS
DIP SW located at the side of the module specifies each I/O module's data allocation (occupied data area).
For example, when the data areas are assigned as shown below:
Module 1
Module 2
Module 3
Module 4
Module 5
Module 6
Module 7
Then the I/O data are assigned as in the table below:
Input Registers (3X)
1 – 4, 257 – 264
Holding Registers (4X)
5 – 8, 265 – 272
9 – 12, 273 – 280
13, 281 – 282
14, 283 – 284
15, 285 – 286
16, 287 – 288
For Coil (0X) and Inputs (1X), addresses 16 times assigned data areas (Data Allocation Type) are allotted with the Data Al-
location Type '1' and '4.' With '8' and '16,' 64 (4 × 16) are automatically allotted.
ADDRESS
DATA FORMAT NAME
1 – 1024
1025
1 – 1024
1 – 256
I
257 – 768
F
1 – 256
I
257 – 768
F
OUTPUT MODE
0
Main bus is used; Red light turns on at RUN LED of the I/O modules.
1
Sub bus is used; Green light turns on at RUN LED of the I/O modules.
1
Main bus is used; Amber light turns on at RUN LED of the I/O modules.
0
Output is invalid; RUN LED of the I/O modules turns off.
4
4
4
1
1
1
1
ADDRESS
POSITION
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 7
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
Digital Output (discrete output)
Main / Sub Switching Command (valid only with SW3-3 set to ON)
Digital Input (discrete input)
Module Status
Error Status
Data Error Status
Analog Input
Analog Input
Analog Output
Analog Output
Coil (0X)
Inputs (1X)
R3-NM1
ADDRESS
POSITION
1 – 64
Slot 1
65 – 128
Slot 2
129 – 192
Slot 3
193 – 208
Slot 4
209 – 224
Slot 5
225 – 240
Slot 6
241 – 256
Slot 7
EM-8354 Rev.19 P. 6 / 8
Advertisement
Table of Contents
