Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select
(JP4)
(JP1)
COM1 RS232/422/485
(JP2)
5
1
5
Select
PS/2 KB/MS
COM2 RS232/422/485
(JP11)
USB 8-9
6
2
6
Select
(JP14)
1 1
(JP4)
COM1 RS232/Power
(JP3)
1
USB 2.0
6
5
Select
COM2 RS232/Power
(JP14)
2
1
Select
(JP2)
4
6
5
COM2
COM 2
2
1
COM 1
COM1
(JP11)
ASMedia
ASM1442
DVI-I
HDMI
ASMedia
ASM1442
USB 0-1 Power
Select (JP5)
LAN 1
1
USB 0-1
USB 3.0
Intel
WGI217LM
LAN 2
USB 4-5 Power
USB 4-5
Select (JP6)
USB 2.0
1
Intel
Line-in
WGI210AT
Line-out
Mic-in
PCIe x16
Realtek
PCI 1
ALC886
1
S/PDIF
2
10
PCI 2
9
1
Front Audio
DIO 3/5/7/9
Output State (JP12)
DIO 11/13/15/17
Digital I/O
Output State (JP7)
1
DIO Power Select
19
2
(JP13)
1 1 1
Chapter 2 Hardware Installation
CPU Fan
COM5
COM6
Chassis
1
9
1
9
1
1
intrusion
(JP3)
2
ISL95820
10
2
10
2
5
+12V
1
Power
System Fan 2
Buzzer
8
Socket LGA1150
Battery
DDR3_1
DDR3_3
DDR3_2
Intel
Q87
Clear CMOS
Data (JP9)
Mini PCIe Signal
ITE
Select (JP15)
1
IT8893E
10
1
USB 2-3/6-7
Power Select (JP8)
12
3
USB 2.0
1
9
1
9
Mini PCIe
Mini PCIe Power Select (JP16)
10
2
10
USB 2-3
USB 6-7
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
LPC
2
12
1
1
11
1
2
Parallel
System Memory
Nuvoton
NCT6106D
Important:
25
26
When the Standby Power LED lights red, it indicates that there is power on the sys-
10
9
COM3
tem board. Power-off the PC then unplug the power cord prior to installing any de-
2
1
vices. Failure to do so will cause severe damage to the motherboard and components.
10
9
COM4
2
1
12
24
ATX
Power
DDR3-1
Channel A
DDR3-2
DDR3-3
Power-on
1
13
Select (JP10)
Channel B
1
Standby
DDR3-4
Power LED
1 2
RSVD
HDD-LED
RESET-SW
RSVD
DDR3_4
Front Panel
11 12
SPI Flash
BIOS
SATA 1
SATA 0
1
1
SATA 3.0
Rear I/O
USB 12-13
System
Power Select
Fan 1
(JP17)
1
Onboard I/O
1
1
SATA 2.0
1
9
1
Storage
1
SATA 5
2
10
2
USB 12-13
Expansion
Features
•
The four DIMM sockets are divided into 2 channels:
Channel A - DDR3_1 and DDR3_2
Channel B - DDR3_3 and DDR3_4
•
Supports
DDR3 1333/1600MHz
•
Supports dual channel memory interface
•
Supports up to 32GB system memory
9
COM 2
COM 1
Standby
Power LED
www.dfi .com
Advertisement
Table of Contents
