Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select
(JP4)
(JP1)
COM1 RS232/422/485
(JP2)
5
1
5
Select
PS/2 KB/MS
COM2 RS232/422/485
(JP11)
6
2
6
Select
USB 8-9
(JP4)
(JP14)
1 1
1
COM1 RS232/Power
(JP3)
USB 2.0
Select
6
5
COM2 RS232/Power
(JP14)
2
1
Select
(JP2)
4
6
5
COM2
COM 2
COM 1
COM1
2
1
(JP11)
ASMedia
ASM1442
DVI-I
HDMI
ASMedia
ASM1442
USB 0-1 Power
Select (JP5)
LAN 1
1
USB 0-1
USB 3.0
Intel
WGI217LM
LAN 2
USB 4-5 Power
USB 4-5
Select (JP6)
1
USB 2.0
Intel
Line-in
WGI210AT
Line-out
Mic-in
PCIe x16
Realtek
ALC886
PCI 1
1
S/PDIF
2
10
9
PCI 2
1
Front Audio
DIO 3/5/7/9
Output State
(JP12)
DIO 11/13/15/17
Output State (JP7)
DIO Power
Select
(JP13)
19
1
DIO
2
1 1
1
•
HD330-H81B has LAN1 only.
•
HD330-H81C: 6 COM (COM1 to COM6).
HD330-H81B/D: 2 COM (COM1 and COM2).
Chapter 2 Hardware Installation
COM5
COM6
1
9
1
9
1
(JP3)
1
CPU Fan
2
10
2
10
2
5
1
+12V
ISL95820
System Fan 2
Power
Buzzer
8
Socket LGA1150
Battery
DDR3_1
DDR3_3
SATA 3.0
Intel
H81
Clear CMOS Data (JP9)
Mini PCIe Signal
Select (JP15)
1
ITE
10
1
IT8893E
12
3
USB 2.0
USB 2-3 Power
Select (JP8)
1
9
1
Mini PCIe
Mini PCIe Power Select (JP16)
10
2
USB 2-3
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Chassis
intrusion
LPC
1
2
12
1
11
1
2
System Memory
Nuvoton
NCT6102D
Important:
25
26
Parallel
When the Standby Power LED lights red, it indicates that there is power on the
10
9
COM3
system board. Power-off the PC then unplug the power cord prior to installing any de-
2
1
vices. Failure to do so will cause severe damage to the motherboard and components.
10
9
COM4
2
1
12
24
ATX
Power
1
13
Power-on
Select (JP10)
1
Standby
Power LED
1
2
Front Panel
11
12
SPI Flash
BIOS
Rear I/O
Onboard I/O
1
1
SATA 1
SATA 0
Storage
System Fan 1
1
Expansion
1
SATA 2.0
1
SATA 5
Features
•
Two 240-pin
•
Supports
DDR3 1333/1600MHz
•
Supports dual channel memory interface
•
Supports up to 16GB system memory
9
DDR3 DIMM sockets
DDR3-1
DDR3-3
Standby
Power LED
www.dfi .com
Advertisement
Table of Contents
