Makita GA7050R Instruction Manual
Hide thumbs
Also See for GA7050R:
- Instructions manual (8 pages) ,
- Instruction manual (104 pages) ,
- Instruction manual (80 pages)
Related Manuals for Makita GA7050R
Summary of Contents for Makita GA7050R
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7050 GA7050R GA9050 GA9050R 010638 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model GA7050 GA7050R GA9050 GA9050R Depressed center wheel diameter 180 mm 180 mm 230 mm 230 mm Max. wheel thickness 6.5 mm 6.5 mm 6.5 mm 6.5 mm Spindle thread No load speed (n )/Rated speed (n) - Page 3 Electrical safety 16. Dress properly. Do not wear loose clothing or Power tool plugs must match the outlet. Never jewellery. Keep your hair, clothing, and gloves modify the plug in any way. Do not use any away from moving parts. Loose clothes, adapter plugs with earthed (grounded) power jewellery or long hair can be caught in moving parts.
-
Page 4: Grinder Safety Warnings
GEB033-7 protection must be capable of stopping flying debris generated by various operations. The dust mask or GRINDER SAFETY WARNINGS respirator must be capable of filtrating particles Safety Warnings Common for Grinding, Sanding, generated by your operation. Prolonged exposure Wire Brushing, or Abrasive Cutting-Off Operations: to high intensity noise may cause hearing loss. -
Page 5: Safety Warnings Specific For Wire Brushing Operations
a) Maintain a firm grip on the power tool and Additional Safety Warnings Specific for Abrasive position your body and arm to allow you to Cutting-Off Operations: resist kickback forces. Always use auxiliary a) Do not “jam” the cut-off wheel or apply handle, if provided, for maximum control over excessive pressure. -
Page 6: Functional Description
Additional Safety Warnings: manual may cause serious personal injury. 17. When using depressed centre grinding wheels, FUNCTIONAL DESCRIPTION be sure to use only fiberglass-reinforced wheels. 18. NEVER USE Stone Cup type wheels with this grinder. This grinder is not designed for these CAUTION: types of wheels and the use of such a product may Always be sure that the tool is switched off and... - Page 7 (in the C direction). To stop the tool from the locked position, pull the switch trigger fully (in the B direction), then release it. Indication lamp (For model GA7050R/GA9050R) 1. Indication lamp 010642 Screw the side grip securely on the position of the tool as shown in the figure.
- Page 8 To remove wheel guard, follow the installation procedure WARNING: in reverse. For tool with clamp lever type wheel guard Never use a more than 6.5 mm thick grinding • wheel. 1. Wheel guard Super flange 2. Bearing box Models with the letter F are standard-equipped with a 3.
-
Page 9: Operation
ALWAYS replace wheel if tool is dropped while • 010844 Mount inner flange , abrasive wheel/Multi-disc and grinding. Ezynut onto the spindle so that Makita Logo on Ezynut NEVER bang or hit grinding disc or wheel onto • faces outside. work. - Page 10 ALWAYS hold the tool firmly with one hand on rear 1. Wire wheel handle and the other on the side handle. Turn the tool on brush and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.
-
Page 11: Replacing Carbon Brushes
2. Inhalation vent injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 010653... - Page 12 Side grip Wheel guard for Depressed center grinding wheel / Multi disc / Wire wheel brush Inner flange / Super flange / Inner flange 102 (Australia and New Zealand only) Depressed center grinding wheel/Multi-disc Lock nut / Ezynut*1 Wheel guard for Abrasive cut off wheel / Diamond wheel*2 Inner flange / Super flange / Inner flange 78 (Australia and New Zealand only) Abrasive cut off wheel / Diamond wheel Outer flange 78 (Australia and New Zealand only)*3...
- Page 13 NOTE: Some items in the list may be included in the tool • package as standard accessories. They may differ from country to country.
- Page 16 Makita Corporation www.makita.com 884937B7...