Servicing Notes - Sony HBD-E385 Service Manual

NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press the [ ] button to turn on the system.
?/1
2. Touch the [FUNCTION] sensor to select "BD/DVD".
3. Touch the [ ] and [ ] sensors simultaneously and hold down
x Z
unit "DEMO OFF" displayed on the fluorescent indicator tube
(around 5 seconds).
Note: When "DEMO LOCK" is displayed, the disc tray lock is not re-
leased by turning power on/off with the [ ?/1 ] button.
ABOUT THE LENS CLEANING
Do not do the lens cleaning with the cotton bud etc. It causes the
trouble.
SECTION 1

SERVICING NOTES

NOTE OF REPLACING THE IC101, IC501 AND IC8001
ON THE MB148 BOARD
IC101, IC501 and IC8001 on the MB148 board cannot exchange
with single. When these parts are damaged, exchange the complete
mounted board.
NOTE OF REPLACING THE IC106 AND IC206 ON
THE MB148 BOARD
Replacement of IC106 and IC206 on the MB148 board used in this
unit requires a special tool.
TEST DISC
Part No.
J-6090-199-A
J-6090-200-A
J-2501-307-A
J-2501-305-A
J-2501-306-A
J-6090-077-A
J-6090-078-A
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select 23.976Hz/1080p.
2. Play "4.Motion picture".
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/S Video/component/HDMI.
Audio:
Speaker out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play "4.Motion picture".
3. Check whether player can play back or not (Check the picture
and sound output).
3. CD (HLX-A1)
Procedure:
Check whether player can play back or not (Check the sound out-
put).
4. HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select "1.Video Signal".
2. Play "1.Color bar 100%" (Check the picture and sound out-
put).
3. Return to Menu.
4. Play "Demonstration 4:3" or "Demonstration 16:9" (Check the
picture and sound output).
HBD-E385/E390/T39
Description Layer
BLX-104 Single Layer
BLX-204 Dual Layer
CD (HLX-A1)
HLX-513 Single Layer (NTSC)
HLX-514 Dual Layer (NTSC)
HLX-506 Single Layer (PAL)
HLX-507 Dual Layer (PAL)
5