Servicing Notes - Sony BDP-CX7000ES Service Manual

BDP-CX7000ES
QQ
3 7 63 1515 0
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
TE
L 13942296513
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE WHEN PARTS THAT CANNOT BE SUPPLIED
ARE REPLACED
There are parts that cannot be exchanged with single parts in this
set. The following parts are damaged, exchange the entire mounted
board.
MB-124-MEGA-EJ board : IC101, IC102, IC103, IC202, IC203,
IC307, IC308, IC501, IC601, IC602,
IC700, IC701, IC8001
VP-062EJ board : IC204, IC301, IC401, IC501, IC602,
IC603, IC606, IC607, IC1003, IC1201
ABOUT THE LENS CLEANING
Do not do the lens cleaning with the cotton bud etc. It causes the
trouble.
NOTE THE OPTICAL PICK-UP BLOCK AND DR-510
BOARD REPLACING
www
Exchange both at the same time when exchange Optical Pick-up
Block (KES-430A) or DR-510 board.
As for the service parts, these two parts are supplied by the set.
.
4
http://www.xiaoyu163.com
SECTION 1

SERVICING NOTES

x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
TEST DISC
Part No. Description
J-6090-199-A BLX-104
J-6090-200-A BLX-204
3-702-101-01 CD (YEDS-18)
J-6090-088-A HLX-504
J-6090-089-A HLX-505
J-6090-077-A HLX-506
J-6090-078-A HLX-507
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select 23.976Hz/1080p.
2. Play "4.Motion picture".
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/S Video/component/HDMI.
Audio:
Speaker out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
* When the output of HDMI is 1080p, the signal of Composite/S
Video/Component are not output.
Q Q
3 6 7 1 3 1 5
It is necessary to lower the output of HDMI to 1080i or less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play "4.Motion picture".
3. Check whether player can play back or not.
(Check the picture and sound output)
3. CD (YEDS-18)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-504/505 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select "1.Video signal".
2. Play "1.Color bar 100%".
(Check the picture and sound output)
3. Return to Menu.
4. Play "Demonstration 4:3" or "Demonstration 16:9".
(Check the picture and sound output)
co
.
9 4 2 8
Layer
Single Layer
Dual Layer
Single Layer (NTSC)
Dual Layer (NTSC)
Single Layer (PAL)
Dual Layer (PAL)
0 5 8 2 9 9 4 2 8
m
9 9
9 9