Table of Contents
Advertisement
Setting
1 )
Press ▲▼ to select the desired items
as below.
Unlocked.
Lock the operation of the control
panel. To unlock, use the remote
control.
Lock the operation of the remote
control. To unlock, use the control
panel.
PIN code lock
J
This function prevents the projector from being
operated by unauthorized persons and provides the
following setting options for security.
1 )
Press ▲▼ to select the desired items
as below.
Off
Unlocked.
Enter the PIN code every time
On 1
turning on the projector.
Enter the PIN code to operate
the projector once the power cord
is disconnected; as long as the
On 2
AC power cord is connected, the
projector can be operated without
a PIN code.
Attention
Whenever you change the PIN code lock setting or the
z
PIN code (the four-digit number), you are required to
enter the PIN code. The "1234" is set as the initial PIN
code at the factory.
Enter a PIN code
Press ▲▼ buttons to enter a number from 0-9. Press ►
button to fix the number and move the red frame pointer to
the next box. The number changes to . Repeat this step to
complete entering a four-digit number.
After entering the four-digit number, press ► button to
move the pointer to "Set" and then a [OK?] confirmation box
appears, select [Yes] and then press <ENTER> button.
If you fixed an incorrect number, use the ◄ button to
move the pointer to the number you want to correct,
and then enter the correct number with the ▲▼
buttons.
If you entered an incorrect PIN code, PIN code and the
number ( ) will turn red for a moment. Enter the
correct PIN code all over again.
PIN code change
J
The PIN code can be changed to your desired four-
digit number.
1 )
Press ▲▼ to select [PIN code change]
and then Press <ENTER> button.
Current Pin code dialog box appears.
z
56
- ENGLISH
2 )
Press ▲▼ to enter the current code.
Press ► button to fix the number and
move the red frame pointer to the next
box.
The New PIN code input dialog box appears.
z
3 )
Repeat these steps to set a new PIN
code.
Attention
Be sure to note the new PIN code and keep it on hand. If
z
you lost the number, you could no longer change the PIN
code setting.
Fan
1 )
Press ▲▼ to select [Fan] and then
Press <ENTER> button.
2 )
Press ▲▼ to select one option .
This function provides the following options in
z
the cooling fans' operation when the projector is
turned off.
Higher-sound than L 2 mode
L 1
and it takes less time to cool the
projector down.
Slower and lower-sound than
L 2
L 1 mode, but it takes more time
to cool the projector down.
Fan control
1 )
Press ▲▼ to select [Fan control] and
then Press <ENTER> button.
2 )
Press ▲▼ to select one among
options as below.
Choose the running speed of cooling fans from
z
the following options according to the ground
elevation under which you use the projector.
Off
Normal speed.*
On 1
Faster than [Off] mode.*
On 2
Faster than [On 1] mode.*
*1 :
Set this function to [Off] when using the projector
in non-high altitude environment.
*2 :
When using the projector in the elevation of
above 1 200 m and below 2 000 m, make sure
[Fan control] is set to [On 1].
*3 :
When using the projector in the elevation of
above 2 000 m and below 2 700 m, make sure
[Fan control] is set to [On 2].
Note
Failure to set the running speed of cooling fans
z
properly may affect the projector life.
The fan noise becomes louder in [On 1] and [On 2].
z
1
2
3
Advertisement
Chapters
Table of Contents
