Table of Contents
Advertisement
PIN code lock
J
This function prevents the projector from being
operated by unauthorized persons and provides the
following setting options for security.
1 )
Press ▲▼ to select the desired items
as below.
Off
Unlocked.
Enter the PIN code every time
On 1
turning on the projector.
Enter the PIN code to operate
the projector once the power cord
is disconnected; as long as the
On 2
AC power cord is connected, the
projector can be operated without
a PIN code.
Attention
Whenever you change the PIN code lock setting or the
z
PIN code (the four-digit number), you are required to
enter the PIN code. The "1234" is set as the initial PIN
code at the factory.
Enter a PIN code
Press ▲▼ buttons to enter a number from 0-9. Press ►
button to fix the number and move the red frame pointer to
the next box. The number changes to . Repeat this step to
complete entering a four-digit number.
After entering the four-digit number, press ► button to
move the pointer to "Set" and then a [OK?] confirmation box
appears, select [Yes] and then press <ENTER> button.
If you fixed an incorrect number, use the ◄ button to
move the pointer to the number you want to correct,
and then enter the correct number with the ▲▼
buttons.
If you entered an incorrect PIN code, PIN code and the
number ( ) will turn red for a moment. Enter the
correct PIN code all over again.
PIN code change
J
The PIN code can be changed to your desired four-
digit number.
1 )
Press ▲▼ to select [PIN code change]
and then Press <ENTER> button.
Current Pin code dialog box appears.
z
2 )
Press ▲▼ to enter the current code.
Press ► button to fix the number and
move the red frame pointer to the next
box.
The New PIN code input dialog box appears.
z
3 )
Repeat these steps to set a new PIN
code.
Attention
Be sure to note the new PIN code and keep it on hand. If
z
you lost the number, you could no longer change the PIN
code setting.
Fan
1 )
Press ▲▼ to select [Fan] and then
Press <ENTER> button.
2 )
Press ▲▼ to select one option .
This function provides the following options in
z
the cooling fans' operation when the projector is
turned off.
Higher-sound than L 2 mode
L 1
and it takes less time to cool the
projector down.
Slower and lower-sound than
L 2
L 1 mode, but it takes more time
to cool the projector down.
Fan control
1 )
Press ▲▼ to select [Fan control] and
then Press <ENTER> button.
2 )
Press ▲▼ to select one among
options as below.
Choose the running speed of cooling fans from
z
the following options according to the ground
elevation under which you use the projector.
Off
Normal speed.*
On 1
Faster than [Off] mode.*
On 2
Faster than [On 1] mode.*
*1 :
Set this function to [Off] when using the projector
in non-high altitude environment.
*2 :
When using the projector in the elevation of
above 1 200 m and below 2 000 m, make sure
[Fan control] is set to [On 1].
*3 :
When using the projector in the elevation of
above 2 000 m and below 2 700 m, make sure
[Fan control] is set to [On 2].
Note
Failure to set the running speed of cooling fans
z
properly may affect the projector life.
The fan noise becomes louder in [On 1] and [On 2].
z
Video delay control
This function allows you to make a digital processing
of a projected image faster.
1 )
Press ▲▼ to select [Video delay
control] and then Press the <ENTER>
button.
2 )
Press ▲▼ to select one item between
[On] and [Off].
Setting
1
2
3
57
ENGLISH -
Advertisement
Chapters
Table of Contents
