Unitronics Vision OPLC V130-33-T38 Installation Manual

Unitronics Vision OPLC V130-33-T38 Installation Manual

Hide thumbs Also See for Vision OPLC V130-33-T38:

Advertisement

Quick Links

Vision™ OPLC™
V130-33-T38/V130-J-T38
V350-35-T38/V350-J-T38
V430-J-T38
General Description
All of the controllers covered in this guide are micro-OPLCs, rugged programmable logic controllers that
comprise built-in operating panels and on-board I/Os.
Item
On-board I/O
Screen
Keypad
Function Keys
Com Port, Built-in
RS232/485
USB device,
mini-B
Com Ports, separate
order, user-installed
* V430J comprises both RS232/485 and USB ports; note that only one channel may be used at a time.
Standard Kit Contents
Item
Controller
Terminal Blocks
Battery (installed)
Slides
(2 sets of key labels)
Mounting Brackets
Rubber Seal
Programming cable
+ RS232 adapter
USB
programming cable
Unitronics
Installation Guide
22 Digital Inputs, including 2 Analog,
2 HSC/Shaft-encoder inputs
16 Transistor Outputs
V130-T38
V130J-T38
2.4"
Yes
None
Yes
None
The user may install a CANbus port (V100-17-CAN), and one of the following:
RS232/RS485 port (V100-17-RS4/V100-17-RS4X)
Ethernet (V100-17-ET2)
Profibus Slave (V100-17-PB1)
V130-T38
V130J-T38
None
Model Dependent
3.5" Color Touch
Yes
Yes
None
None
Yes
Yes
Yes
Yes (2 parts)
Yes
Yes
None
V350-T38
V350J-T38
None
Yes
Yes
None
V350-T38
V350J-T38
Yes
V430J-T38
4.3" Color Touch
Yes*
Yes*
V430J-T38
None
Yes (4 parts)
None
Yes
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vision OPLC V130-33-T38 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Unitronics Vision OPLC V130-33-T38

  • Page 1 Standard Kit Contents V130-T38 V350-T38 V430J-T38 Item V130J-T38 V350J-T38 Controller Terminal Blocks Battery (installed) Slides None None (2 sets of key labels) Mounting Brackets Yes (2 parts) Yes (4 parts) Rubber Seal Programming cable None + RS232 adapter None programming cable Unitronics...
  • Page 2: Alert Symbols And General Restrictions

    All examples and diagrams are intended to aid understanding, and do not guarantee operation. Unitronics accepts no responsibility for actual use of this product based on these examples. Please dispose of this product according to local and national standards and regulations.
  • Page 3: Panel Mounting

    4. Tighten the bracket’s screws against the panel. Hold the bracket securely against the unit while tightening the screw. 5. When properly mounted, the controller is squarely situated in the panel cut-out as shown in the accompanying figures. V130/V350/V130J/V350J Unitronics...
  • Page 4 DIN-rail Mounting (V130/V350/V130J/V350J) 1. Snap the controller onto the DIN rail as shown in the figure to the right. 2. When properly mounted, the controller is squarely situated on the DIN-rail as shown in the figure to the right. Unitronics...
  • Page 5: Wiring Procedure

    - Inputs 1 and 3 can function as either counter reset, as normal digital inputs, or as part of a shaft- encoder. If inputs 0 and 2 are set as high-speed counters (without reset), inputs 1 and 3 can function as normal digital inputs. Unitronics...
  • Page 6 Inputs 14/15: Set as Digital or Analog Set to JP2 (Input 14) JP1 (Input 15) Digital* Analog Analog Inputs AN0/AN1: Set Type Set to JP4 (AN0) JP3 (AN1) Voltage Current* *Default settings I/O Wiring npn (sink) Input Input wiring HSC input wiring Unitronics...
  • Page 7 HSC input wiring Shaft-encoder Analog Input Analog input wiring, current (2/3-wire) Analog input wiring, current (4-wire), voltage Shields should be connected at the signal’s source. The 0V signal of the analog input must be connected to the controller’s 0V. Unitronics...
  • Page 8: Power Supply

    To maximize system performance, avoid electromagnetic interference by: Mounting the controller on a metal panel. Connect each common and ground connection directly to the earth ground of your system. For ground wiring uses the shortest and thickest possible wire. Unitronics...
  • Page 9 To do so, remove the RS485 connector (pins 1 & 6) from the PLC and connect a standard RS232 programming cable. Note that this is possible only if DTR and DSR signals of RS232 are not used (which is the standard case). Unitronics...
  • Page 10 ** Causes the unit to function as an end unit in an RS485 network USB Port The USB port is not isolated. Caution Make sure that the PC and the controller are grounded to same potential. The USB port may be used for programming, OS download, and PC access. Unitronics...
  • Page 11 Vision™ OPLC™ Opening the Controller Before performing these actions, touch a grounded object to discharge any electrostatic charge. Avoid touching the PCB board directly. Hold the PCB board by its connectors. 1. Turn off the power supply, disconnect, and dismount the controller. 2.

Table of Contents