Subscribe to Our Youtube Channel
Related Manuals for Xtreme Power Conversion P90-BP36
Summary of Contents for Xtreme Power Conversion P90-BP36
- Page 1 P90-BP36, BP48, BP72 External Battery Packs User & Installation Manual www.xpcc.com | © 2016 Xtreme Power Conversion Corporation. All rights reserved. (Rev 1/13/16)
-
Page 2: Table Of Contents
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Table of Contents Important Safety Instructions...............3 Product Overview and Setup................3 Rear Panel View..........................3 Installation and Setup with UPS......................4 Type of Battery Required................5 Battery Replacement..................5 P90-BP36............................5 P90-BP48............................7 P90-BP72............................10 Wiring Diagram..................12 P90-BP36............................12 P90-BP48............................13 P90-BP72............................14 Storage &... -
Page 3: Important Safety Instructions
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Important Safety Instructions Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully. -
Page 4: Installation And Setup With Ups
P90-BP36, BP48, BP72 User’s Manual External Battery Packs 1. DC connector : connects to either UPS or 2nd battery box 2. DC breaker: Battery over-current protection breaker Installation and Setup with UPS Unpacking & Inspection 1. Remove the battery box from the packing. -
Page 5: Type Of Battery Required
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Connecting with UPS and Other Battery Box Follow below installation chart to connect with UPS and other battery box with included cable. 1st Battery Pack 2nd Battery Pack Type of Battery Required... - Page 6 P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 3: Remove the fixed part of the front panel by removing the 2 screw present. Step 4: Remove the metal top cover of the battery box by unscrewing 6 screws present on the two sides (3 on the right side and 3 on the left side), 3 screws on the top and 4 screws on the back side.
-
Page 7: P90-Bp48
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Note: To install the second string of batteries, repeat the same procedure on the battery hold down brackets on the right side of the battery box. Step 6: Now, it is possible to put all batteries inside the unit by following the below picture (the following drawing are indicates the wire fastener positions for the correct battery placement). - Page 8 P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 2: Remove the removable front panel part by pulling it from the lower extremity Step 3: Remove the fixed part of the front panel by removing the 2 screw present. Step 4: Remove the metal top cover of the battery box by unscrewing 8 screws present on the two sides (4 on the right side and 4 on the left side), 3 screws on the top and 4 screws on the back side.
- Page 9 P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 5: Once the battery box is opened, remove the battery hold down brackets present on the left side of the bat- tery box by unscrewing the 2 screws on each bracket.
-
Page 10: P90-Bp72
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 8: Put all batteries inside and secure in place with hold down brackets. Note: To install the second string of batteries, repeat the same procedure on the right side of battery box. - Page 11 P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 4: Remove the metal top cover of the battery box by unscrewing 8 screws present on the two sides (4 on the right side and 4 on the left side), 3 screws on the top and 4 screws on the back side.
-
Page 12: Wiring Diagram
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Step 8: Put all batteries inside and secure in place with the hold down brackets. Note: To install the second string of batteries, repeat the same procedure on the right side of battery box. -
Page 13: P90-Bp48
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Picture example as below: 450M 150M 350M 150M 350M 450M Note: The cable connection from the external battery connector to PCB is already present inside the battery box. All the other cable connections should be made in accordance with the above wiring diagram. -
Page 14: P90-Bp72
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Picture example as below: 260MM 280M 220MM 300MM 280M Note: The cable connection from the external battery connector to PCB is already present inside the battery box. All the other cable connections should be made in accordance with the above wiring diagram. -
Page 15: Storage & Maintenance
P90-BP36, BP48, BP72 User’s Manual External Battery Packs Picture example as below: 240M 280M 380M 380M Note: The cable connection from the external battery connector to PCB is already present inside the battery box. All the other cable connections should be made in accordance with the above wiring diagram.
Need help?
Do you have a question about the P90-BP36 and is the answer not in the manual?
Questions and answers