Advertisement
[10] TEST COMMAND, TROUBLE CODES
1. Entering the test command mode
To enter the serviceman test command mode, press the keys as follows:
→
→
→
[#] key
[*] key
[C] key
[*] key
To cancel the test command mode, press the [CA] key.
2. Key rule
[10KEY]:
Entry of MAIN CODE/SUB CODE
Selection of an item
Setup of an adjustment value in case of test commands for adjustment
←
→
[
/
]:
Selection of MAIN CODE/SUB CODE
Selection of an item
[OK (ENTER)/START]:
Settlement
<In case of test commands for print>
[OK (ENTER)]:
[START]:
[C]:
(Interrupting operation check) Returns to the upper hierarchy.
In case of test command of operation check, terminates the operations.
[CA]:
Exits from the test command mode.
For a test command of adjustment, the display returns to the initial display (00-00).
3. List of test commands
Main
Sub
code
code
1
01
Mirror scan (SCAN CHK)
02
Mirror home position sensor (MHPS) status display
(MHP-SENSOR)
06
Mirror scan aging (SCAN AGING)
2
01
Single Paper Feeder (SPF) aging (SPF AGING)
(Disabled when set to OC) (Executable only when the
SPF is installed.)
02
SPF sensor status display (SPF SENSOR) (Disabled
when set to OC) (Executable only when the SPF is
installed.)
03
SPF motor operation check (SPF MOTOR CHK)
(Disabled when set to OC) (Executable only when the
SPF is installed.)
06
RSPF resist clutch operation check (RSPF RES.CHK)
(Enabled only when RSPF is set.) (Executable only when
the RSPF is installed.)
08
SPF paper feed solenoid operation check (SPF SPUS
CHK) (Disabled when set to OC) (Executable only when
the SPF is installed.)
09
RSPF reverse solenoid operation check (RSPF SPFS
CHK) (Enabled only when RSPF is set.) (Executable only
when the RSPF is installed.)
10
RSPF paper exit gate solenoid operation check (RSPF
SGS CHK) (Enabled only when RSPF is set.)
(Executable only when the RSPF is installed.)
3
03
Shifter operation check (SHIFTER CHK)
5
01
Operation panel display check (LCD/LED CHK)
02
Fusing lamp, cooling fan operation check (HT LAMP
CHK)
03
Copy lamp ON check (C-LAMP CHK)
6
01
Paper feed solenoid (CPFS1, CPFS2, MPFS) operation
check (PSOL CHK)
02
Resist roller solenoid (RRS) operation check (RES.R
SOL CHK)
7
01
Check of warm-up display and aging with JAM (W-UP/
AGING)
06
Interval aging (INTERVAL AGING)
08
Shift to copy with warm-up display (W-UP C-MODE)
Settlement (Without print)
Settlement/Print
Contents
AR-M150/M155/M155X TEST COMMAND, TROUBLE CODES 10 - 1
Main
Sub
code
code
8
01
Developing bias output (DVLP BIAS SET.)
02
Main charger output (Grid HIGH) (MHV(H) SET.)
03
Main charger output (Grid LOW) (MHV(L) SET.)
06
Transfer charger output (THV SET.)
9
01
Duplex motor normal rotation check (DPLX ROT.)
(Enabled when Duplex setting is ON) (Executable only
when the RSPF is installed.)
02
Duplex motor reverse rotation check (DPLX ROT.REV.)
(Enabled when Duplex setting is ON) (Executable only
when the RSPF is installed.)
04
Duplex motor rotating speed adjustment (DPLX
ROT.SPEED) (Enabled when Duplex setting is ON)
(Executable only when the RSPF is installed.)
10
00
Toner motor operation (TONER MOTOR)
14
00
Cancel of trouble other than U2 (TRBL CANC.)
16
00
U2 trouble cancel (U2 TRBL CANC.)
20
01
Maintenance counter clear (M-CNT CLR.)
21
01
Maintenance cycle setting (M-CYCLE)
22
01
Maintenance counter display (M-CNT)
02
Maintenance preset display (M-CNT PRESET)
04
JAM total counter display (JAM TTL CNT)
05
Total counter display (TTL CNT)
06
Developer counter display (DVLP CNT)
08
SPF counter display (SPF CNT) (Disabled when set to
OC) (Executable only when the SPF is installed.)
11
FAX-related counter display (Executable only when the
FAX is installed.)
12
Drum counter display (DRUM CNT)
13
CRUM type display (CRUM TYPE)
14
ROM version display (ROM VER.)
16
Duplex counter display (DPLX CNT) (Enabled when
Duplex setting is ON) (Executable only when the RSPF is
installed.)
17
Copy counter display (COPIES CNT)
18
Printer counter display (PRT.CNT)
19
Scanner mode counter display (S-MODE CNT)
21
Scanner counter display (SCAN CNT)
22
SPF JAM counter display (S JAM CNT) (Disabled when
set to OC) (Executable only when the SPF is installed.)
Contents
Advertisement
