Table Of Contents - Intech Instruments Z-2400-A2 Series Installation Manual

Z-2400-A2 Wireless Node Installation Guide Index.
Description.
Ordering Information.
Specifications.
Analogue Input 1~2 Specifications.
Digital Input 1~4 Specifications.
Digital Output 3~4 Specifications.
Relay Output 1~2 Specifications.
Analogue Output 1~2 Specifications.
General Specifications.
Physical Layout Z-2400-A2 Series.
Front Panel Connections and LEDs.
Terminal Connections.
Diagnostic LEDs.
RF Signal Quality LED Indication.
Output, Input and Repeater Node Network Status LED Definitions.
Power and ZigBee Network LED Indication.
Z-2400-A2I Dip Switch Positions for Input to Output Installations.
ZigBee Mesh ID.
Programming the Z-2400-A2 Series.
uP Configure Software.
Installing uP Configure.
Z-2400-A2 USB Connection.
Using the uP Configure Software - version 1.2.8.0 or later.
Configuring the Z-2400-A2O.
Configuring the Z-2400-A2I.
Configuring the Z-2400-A2R.
Connecting up the Z-2400-A2 Series.
Z-2400-A2 Series Power Supply Connection.
Z-2400-A2I Analogue Input Connections.
Connecting RTDs to the Z-2400-A2I Analogue Inputs.
Connecting Thermocouples to the Z-2400-A2I Analogue Inputs.
Connecting Voltage Signals to the Z-2400-A2I Analogue Inputs.
Connecting Current Signals to the Z-2400-A2I Analogue Inputs.
Connecting Pulse, Frequency & On/Off State Signals to the Z-2400-A2I Analogue Inputs. Page 15
Z-2400-A2I & Z-2400-A2O Digital Input/Output Connections.
Connecting to the Z-2400-A2I & Z-2400-A2O Relay Outputs.
Connecting to the Z-2400-A2I & Z-2400-A2O Digital Outputs.
Connecting Pulse, Frequency & On/Off State Signals to the Z-2400-A2I & Z-2400-A2O
Digital Inputs.
Z-2400-A2O Current Loop Outputs.
Z-2400-A2 Series Wiring, Installation and Maintenance.
Z-2400-A2 Wiring and Installation.
Z-2400-A2 Commissioning.
Z-2400-A2 Maintenance.
Troubleshooting.
Considerations & Limitations for Z-2400 Network Systems.
Antenna Options for Z-2400 Wireless Series.
®
ZigBee is a registered trademark of the ZigBee Alliance, Inc.
Product Liability. This information describes our products. It does not constitute guaranteed properties and is not intended to affirm the suitability of a
product for a particular application. Due to ongoing research and development, designs, specifications, and documentation are subject to change
without notification. Regrettably, omissions and exceptions cannot be completely ruled out. No liability will be accepted for errors, omissions or
amendments to this specification. Technical data are always specified by their average values and are based on Standard Calibration Units at 25°C,
unless otherwise specified. Each product is subject to the 'Conditions of Sale'.
Warning: These products are not designed for use in, and should not be used for patient connected applications. In any critical installation
an independent fail-safe back-up system must always be implemented.
2
Page 3
Page 3
Page 4
Page 4
Page 5
Page 5
Page 5
Page 5
Page 5
Page 6
Page 6
Page 6
Page 7
Page 7
Page 7
Page 8
Page 8
Page 8
Page 8
Page 8
Page 8
Page 9
Page 10
Page 10
Page 11
Page 13
Page 13
Page 13
Page 14
Page 14
Page 14
Page 15
Page 15
Page 16
Page 16
Page 17
Page 17
Page 18
Page 18
Page 18
Page 19
Page 19
Page 20
Page 20
Page 20